Paul thanks for your reply. I have looked for information about these traps because I have two RMSH-2 traps and I thought about using one for the carrier gas (He) and the other for the FID hydrogen. Anyway, I'm going to buy the hydrogen trap. Thanks …
In my experience, usually when a method fails to download to a 7820A GC it means that one of the zones on the GC is in a faulted state. This does not always get reported in the instrument actuals in ChemStation, so the best way to double-check this is…
Hello howard_sanford ,
I tried clearing the preferences for IDBrowser, and it did work when I used the old PCDL, but the "m/z" column in ID Browser did not show anything. So, I did it again and for the second time, the m/z of features showed up, but…
Dear Agilent,
I am trying to perform a "backflush scouting run", using the nice backflush wizard option in Chemstation rev. C.01.10, for configuration of a useful backflush time to my GC method. However, the backflush wizard unfortunately stops after…
Hi chemist85 , I'd like to inform you that our instrument problem was solved, and yes it caused by the broken UPS, the output voltage is dropped to 160 volts when igniting the plasma, and also the voltage was not stable at all and unfortunately, it also…
Yes, it is off on all gasses, always by roughly 20% (occasionally nearly 30% or as low as 15%, depending on the instrument). Air, Hydrogen, Makeup (N2), carrier (H2 or He) on every instrument (12 GC and 3 GC/MS, which haven't been evaluated). It's also…
It knows that the electrometer board is plugged into the main board and expects everything else to be there, too. The simplest suggestion is to power down, unplug the GC from the wall, remove the FID electrometer from the main board, button it back up…
My GC-FID says the following when I change the split ratio form 50:1 to 200:1: Front inlet flow limited. I dont know what I need to change further so it won't be limited. Does anyone have some tips
Hello,
We have a GC 7890A model equipped by tray (SN#CN90452624) and Autosampler (SN#7683) I am receiving the following message while trying to run sample followed by a shaking arm and beeping noise. Any help on what might cause the problem is greatly…
Good day Agilent, I am really humbled to join the community. I have a few inquiry I would like to make.
I am having a very noisy baseline every time I try to bake out using both ECD and FID,
When I analyze acetaldehyde using the FID it keeps the noise…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...