Hello, I have initialization problems with my software, MassHunter Workstation software, LC/MS Data Acquisition for 6400 series triple quadrupole Version B.08.00, a service engineer from the brand representative recommended that I uninstall the software…
Dear Community
We faced problems with our GC 7890B which is connected to a Leco Pegasus BT. Since this week we have a really high noise, which comes regularly every 5seconds. We already cleaned FID many times, replaced Jet and built the FID out an in…
Did you finally determine the cause of the inconsistent results? I'm having a similar issue with a different instrument. I have gone through my troubleshooting list and failed to identify the issue.
Hello
We are working on developing a method for detecting mineral oil contamination (MOSH and MOAH) in edible oils. We are able to get MOSH (mineral oil saturated hydrocarbons) to work well, but when we inject a sample for MOAH (mineral oil aromatic…
Here is a collection of Agilent 7890, 8860 and 8890 GC Resources. Links to user manuals, troubleshooting resources , tools and supplies on Agilent.com . Go to Collection of GC/MS Resources to view GC/MS information.
Agilent 8890 GC User Manuals
…
I think our only problem at the moment is a hardware issue (EPC failing to shut makeup gas OFF when called for) that prevents FID ignition… we’re putting in a call for service to resolve that. I’ll be working to resolve user error (Comments Edited by…
Hello,
Are you sure the end tip of the PLOT column ends up (and 2 mm withdrawn) inside the FID Jet?
Any problems when igniting the FID?
FID Jet could be contaminated from PLOT stationary phase particles ..
Best regards -
Lars
There are two log files. The main file looks like a lot was going on.
I went back and did a search for "error" and found the following:
Could not create system restore point, error: 0x80070422. Continuing...
Error 0x80096010: Failed authenticode…
No I haven't. But I think that is the only solution. Perhaps there are somehow misalignment making it not robust and the needle fail to go in the vial and abort the run randomly. . I will do the auto-reference and I will wait and see how frequent the…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...