Hello everyone!
I'm currently working on a new (for my company) method of quantifying acrolein by GC-FID. I have a big problem with the appropriate weight of the standard. According to the article, I should add the right amount of acrolein to the CS2…
Thanks, Marty! I'm unfamiliar with intelligent reporter, but it looks like that's what I need. This would be for a single injection. I would need it to display as another line under the main results, with an obvious notation, like pass/fail or reportable…
Hello, I have the new MassHunter. Well, my P/A factor has failed. :-( do I correct this? I don't understand how to correct it. I am supposed to select a measurement from the "Load Mass List from Method". and added it. Unfortunately, the Current Value…
We are trying install OpenLab LTS 01.11 Aug 2022 onto our Windows 10 system; however, the System Preparation Tool states that the Check Pending Reboot step fails even after rebooting the computer.
This is a known issue with the software, but there is…
The signal count is lower between the DFTTP/Degrad check with each analytical run. The analytical run acquisition is pointing to the dfttp tune file.
A new syringe has been replaced. Inlet maintenance is done every 4-5 analytical runs; this instrument…
Hello, friends! We have installed a new AAS 280FS device. After installation, the device fails Frequency Diagnostic and Power supply Diagnostic tests according to the SVD software. Please advice, what we can do? Thank you.
We have intention to upgrade existing Chemstation B version to OpenLab Chemstation C.01.10 version for 6890N and 6890A GC both equipped with TPI inlet (from VAR) and FID.
We are not sure if the upgraded OpenLab CDS able to recognise or support TPI inlet…
Thanks for your quick response
but i want to put this limits ( for example 90% to 110%) in my CC editor and in my report called the final result (for example 95%) PASSED and (for example 85%) FAILED. So , how can i translate this limits for different…
Hi all,
I work on a 6470A QQQ. The MS was shut down for maintenance, change of oil of the rough pump, source cleaning, AJS ESI needle replacement and capillary replacement were performed.
Rough vac and high vac values are better than before shutting…
Hello igorvlad
I’m sorry for the delayed reply to your message. Do you still need assistance with this? If you do, please take into consideration the notes below. However, if the issue was resolved, could you please share what the resolution was?…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...