Thanks for the answer but I still fail to understand.
If helium pressure at the inlet of the TD is constant and only controlled manually, why can't it be controlled by the AUX EPC?
Can't I just connect one of the outlet of the AUX EPC through a t…
We fail to properly communicate with the turbo V70 controller, model 969-9507, using RS232.
The communication is ok for all commands that do not answer with more than two bytes, like start and stop.
However, commands supposed to answer with more than…
This document contains a list of FAQ and troubleshooting links for Agilent Cell Analysis products. See also Collection of Cell Analysis Resources .
FAQs
Seahorse:
Agilent Seahorse XF Imaging and Normalization FAQs
Agilent Seahorse XF Real…
Hi community
we getting error message (Configuration system failed to initialize. Chemstation will shutdown now) when we trying to launch Chemstation ,we try rename conf. files in C:\Chem32\1 but that not work.
I appreciated any help .
Dheya
Hi Everyone
This is my first post here in this community. And I really hope to get some ideas to fix my problem, since i'm getting slowly desperate!
So here's my problem: We have some really bad contamination/peaks on all our polar Systems:
I…
Hi,
I get this Front Inlet: Septum purge Pre shutdown warning with Error code: 20401202 with cause showing EPC module is going into a shutdown. This warning showed up immediately after the maintenance was performed to change the septum and SSL liner…
We have a GC-MS instrument and it works well. Recently we installed a new column which connected to FID detector. Now we want to run a method with GC-FID/MS. However, we observed the peaks only in MS spectrum without FID spectrum. We need help with the…
Hi JF_Fortin ,
As andyg mentions, starting with Qual B.08.00 SP1 and Version 10.0 the handling of data files with only 2D detector data has been improved to automatically open non-MS chromatograms.
In previous versions the message you are seeing is…
This file contains a list of 59 commonly used consumables and parts for 7890 GC .
Upload this file to your Smart Alerts software to automatically add these parts to the Master Parts List
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...