Once the lamp got ignited the light arc between anode and cathode has been sustained.
The referring anode voltage typically stabilizes after a certain time and can be heavily influenced by environmental conditions.
Fluctuations in the anode voltage…
Hello,
This one could be difficult. 2 things come to mind. First make sure you are not saving the folder of the batch into another batch folder. This will void the .b folder and failed to read correctly. Go see if you can into the drive X:Agilent\ICPMS…
Thank you Kbusch.
Is there any videos that can show me how to move needle arm out of the seat. I tried to go through Lab Advisor but the arm does not go to maintenance mode. Lab Advisor timed out and failed to connect to LC. I shut down the sampler…
Hello collrube ,
No such thing as a dumb question
Just so I can understand the question better, do you mean that you used to have a 5890 GC FID system, and you replaced that with an 8890 GC FID system? Or do you mean that your FID on the 5890…
Dear all,
we have not measured many samples, only some organic samples. Could someone please explain, what cause the RF coils change the color like this? Does it affect the plasma ignition? How to clean it properly?
Is it correct, I take the coils…
Your controller is going in Auto Tune
Autotuning condition is shown when the controller has delivered an output power level higher than a typical value, but the pump is still not reaching full speed value.
It does not matter if it is a normal start…
Hello SimonHarries ,
The only time I have heard an FID trying to re-light itself is when the baseline of the FID dropped below the Lit Offset value.
What is your baseline at (in pA) when the FID is lit, but not running sample? And what is your lit…
May I ask? Did you take an official FLD training? Working on the innards of an FLD usually is for trained staff only. Many things can go wrong here, e.g. replacing the lamp is much different to replacing the lamp on a UV detector. One can screw up the…
Hello! I followed this tutorial part D Linked Dual GC Signals 1 aliquot /cfs-file/__key/communityserver-discussions-components-files/152/0020.DualTow7890EnvMH.pdf to sample 1 aliquot through both the front and back autosamplers, both columns, to both…
Slightly related: As part of a new lab setup, I decided I could greatly save having to replace cylinders if I ran my FID on a one-fifth flow of pure oxygen instead of compressed air.... Maybe you could guess the result. Every ignition was a detonation…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...