This may be due to several factors. First of all, make sure that all plasma monitor connections and cables are properly connected and not damaged. Also check that there is sufficient gas flow (eg argon) to maintain the plasma. Check the cleanliness and…
Hello all,
I´m facing a Silicium contamination in ICP-MS analysis, I have used a 7800 ICP-MS.
I have digested my samples with HF, HCL and HNO3 and neutralized it with boric acid, after the analysis I have Silicium CPS has increased around 30%.
…
Hi Layden,
your source has died (normal ratio Amps/Volts should be starting at 1.9/2.7). Each year you will find a decline in Amps until it has reached 1.6, then it will give a red bar. In your case it's 0, so the filament is probably broken - your…
I have almost the same system as shown in the picture for over a year now. The application was supplied by Da Vinci Laboratory Solutions in the Netherlands. It is a Mettler TGA 2, with a Gerstel MPS autosampler on a Agilent GCMS(MS) with a CIS injector…
Thank you. I contacted the support. I just had to login into agilent subscribenet and download the latest version after entering the authorization key.
Hello,
That looks like a standard IS calibration using area percent. The purity of the standard can be entered as the compound multiplier. I would start by searching the help for calibration, internal standard, and mass percent calculations. You can…
Hello Lucas_S ,
Based on your follow-up explanation in this discussion -
(+) Macro for Batch Export of CSV in OpenLab CDS C.01.10 to a unique archive. - Forum - Chromatography Software - Agilent Community
I don't believe this macro could be easily…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...