I am operating the MPAES 4210 with the Agilent 4107 Nitrogen Generator. I have run the Gas Test (Plasma Off) and everything passes. When I run the Plasma Ignition Test, the plasma ignites (passed), but after 20-30 seconds, the plasma shuts off. An error…
7890A GC/5975 MS/E.02.02 SP2
Sequence is stopping constantly with the following log book message: "The run was stopped by the instrument's stop button or stop input. The GC Failed to Start."
Found that exact error in the KBR - " Known Problem Report…
I apologize because this is a very blind question- New IT guy to the company and previous didn't have good documentation on this application.
I have a user who is getting the attached error whenever they try and open Sequence Manager or open Bioconfirm…
Hello all, we have acquired a 120V 7820 ex-US (2011 build w. UEPC´s for 2x FID) and converted to our local 230V by swapping heater shroud & AC board. After that it initially would not heat higher than 280C but bail out with a thermal shutdown. Fan was…
This 6890 is code named FIDDY because of its dual Flame Ionization Detectors. The SF FBI donated it to UC Davis Chemistry over 10 yrs ago. It is used to teach Chemistry majors gas chromatography and replaced an old Varian 3800 with a chart recorder!
In detail, you can follow below link to resolve this type of problem.
https://community.agilent.com/technical/gc/w/wiki/7889/troubleshooting-an-fid-not-igniting
Hopefully, problem will solve..
New FID Jet!
The latest FID jet is intended for use in 6890/7890/8890/8860/8850/9000 GC models
The legacy jets will not work in the 8890/8850/8860/9000 GC models
The new jet makes installing the column seamless with a conical shape to direct the…
Hello
I am having a hard time trying to figure out how to only display one FID signal on a report from a dual injector GC system in OpenLAB 2.4. The calibration that was run used the dual injector setting, but when we were running test samples we only…
I'm currently encountering a challenging issue with MassHunter Acquisition Software that has significantly hindered my workflow. I am hoping to leverage the community's expertise to find an effective resolution.
Switching from MRM to dMRM Settings Error…
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...