I have the same problem when the instrument is switched to work at a negative mode. do you think my Medusa power supply also failed? what is the part#? Is G1969-65360 the right part #?
Thanks
Hi Brenda, Whats the total flow setting on the inlet set at? If the total flow is set high because of a high split can be one reason. I suspect this is more of a hardware fault like a blocked split line or a split valve problem. Shutdown #4 This message…
Hello Maybe this question be out-of-date for the current time but I will be appreciate for everyone that can help me. I have few Varian CP-3800 GC in our Lab, unfortunately some of them failed to operate because of electrical board part. I requested these…
In our company we are using a GC-FID Agilent technologies 7820A connected to a Headspace 7697A from Agilent also,
and we are not able to transfer some methods into our system when the carrier gas is Nitrogen.
Our team is in charge of the Method transfers…
Dear Team,
Is it OK to use 8860 system for USP467, residual solvents analysis ? Literature that is available is mainly on 8890 but 8860 can also be used ? Agilent do have a blood alcohol analysis app note on 8860 with HS, 1 SSL, a Tee connection, 2…
Hello,
We just recently got a new tapestation 4150 in our lab, which we're trying to set up. As a part of the setup I rand the full system diagnostics to see if the system is working with the Tapestation Test Tape. Everything runs successfully and the…
Hello dexter91, I need to have the column configuration from your system in order to give you a proper answer: are you using only 1 column with a splitter at the end to split it to the MS and the FID or you have 2 columns configured, 1 for each detector…
Hello,
Please mention the instrument you are trying to work with.
Please see the following for GC:
GC Signal Conversion Factors
Use to convert to display scale units
Use to convert to unscaled…
We currently use Agilent 7890A GC with S/SL injector and FID detector using a capillary column for the analysis of crude oil composition upto C35. The remaining compounds will be reported as C36+. The temperature program is from 30 Deg to 325 Deg, We…
Hello, thanks for update (I wonder if my memories were incorrect,,, Your question is classed "difficult" ...... Let me start easier one! The visible lamp is not required replacing. It seems working without error. that is typical "bulb" , if id is out…
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...