Hi azrael, The FID is not a pressurized detector so there is no pressure test. You may wish to explore our GC Fundamentals series on our website. See Below for a link Fundamentals of Gas Chromatography (GC) - Part 1 | Agilent Regards James
Hi Mike,
Thanks for the reply but i have run the instrument performance test it was ok.
Customer is using quarts cuvettes.
another issue we found when running wavelength accuracy and precision run from the validation, it missing one or two wavelength…
We have a 7890B that was configured with an MSD but is being reconfigured for a different analysis. It is now running an FID/TCD method, and the aux detector has been disconnected and unconfigured. The MS/Aux Det button on the GC keyboard says no aux…
Hello,
I am having an issue getting the system pressure test to pass. I have referred to the manual and followed all the steps, and have checked for any leaks (there are no visible leaks) and the leak test on the system is also passing - yet the pressure…
Hi This morning the check Tune failed. After adjusting MS1, the tune passed with warnings. Then I decided to autotune. It went through many of the steps until "Enhanced" failed. I am not sure what this step is. Not easy to find any documentation. Can…
When Air gap is 0.2 and the flow rate is 2.1 ml/min then the peak area found 287 by FID but when the air gap is 0 and flow rate is 1.47 ml/min then the area reduced to 141. Where analysis performed by Autosampler.
I think we do this at my lab but not with a valve. We use a plot column and anayze headspace above a water sample. We test for methane ethane ethene and propane useing an FID. The integrated gastight syringe with a valve in it from Fisher helps. We use…
Hello everyone
I have 3 error messages from the Agilent infinity ii 1260 SFC Multi sampler:
1- Metering device Movement Failed ( EE25444.0) 2- Taking needle From park station failed ( EE25105.201 ) 3- Axis did not reach its target position in time…
Using OpenLab EZChrom A.04.1.0.0 with a 6890N GC-FID this error occurs
The IS dept have looked into this and have commented that the systems log mentions that the instance has reached its maximum size of 32MB. We have been running the same system…
Hi, I have the same problem as well. We are using LC 1220 Infinity series. We tried flushing the system with isopropanol for 10 minutes just in case the bubbles are present. However, this does not solve the problem. The pump failed to get ready within…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...