Hello, I have a G1321B that showed errors during the OQPV. The FSE changed the flash lamp Iand the Intensity test is OK arround 10000 counts buen the and Raman ASTM Signal/Noise fail. I want to know if there are another test to do.
Hello,
I am expeirencing the same issue after having to reload E.02.02.1431. The quant report prints as one job and the chromatogram and the spectra reports (I'm printing a detailed report) print as a second job.
I've done as ron_tackett mentioned…
Hello vanphu, Thanks for the model information. On power on, the motor needs to move the pump to specified positions and if it fails to do so in a range of motor steps, it can give the error you mentioned. We advise to leave the pump stroke in auto to…
Hello,
Our lab currently uses a headspace-GC-FID to analyze for ethanol in blood samples. We have a multi-level, internal standard calibration curve as well as control samples at various concentrations that are analyzed in a sequence. Is there a way…
When doing autotune I get high precursor in mass 502. I get 12.79% and the limit is 12%. The manual says that it could be contaminated. The equipment has had preventive maintenance recently but it has now this problem. Previously it had a ratio of mass…
Anyone have experience with a 7890B causing abnormal signal attenuation and more signal noise than normal? The attenuation problem - the detector's AIB signal has a maximum signal of ~ 69,000 uV however the signal now tops out at ~30,000 uV in the ChemStation…
Hello lperry ,
The document below explains what that error is, essentially it could be that an ALS is not ready for injection, or some other piece of hardware connected to the GC.
6890 GC Not Ready Messages (agilent.com) (bottom of page 9).
…
I changed my acquisition method from using front FID to back FID. I changed this in the acquisition method detector, signals, and columns sections. On my status tab, the detector is still showing front FID and the online signals is showing no options…
The Digest of upcoming webinars has been updated as of January 4.
Notable additions include:
Spectroscopy Digital Workshop & Bootcamp (16)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from contaminants…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...