Hi,
I plan to attempt some SimDist analysis in accordance with D2887 on my agilent GC-FID. I was hoping that I could achieve this without additional software (i.e. just through manual manipulation of the data acquired by Chemstation), but apparently…
Hi everyone.
We have a 8890 Agilent GC with nickel catalyst and FID detector. We would like to use hydrogen as carrier gas, but we don’t know the right flow rates, because the manual is indicating flow rates only for using helium as carrier gas.
For…
Turning off the systems on Friday night that need to be ready to go on Monday morning is not recommended. It can take quite some time for a GC/MS to come back up to operational after being shut down. Even cooling the temperatures all down and then heating…
Hi, I would suggest to test the same without column installed to the FID. If problem looks similar check for leaks at the FID gas lines and clean the FID. If not clean the inlet and replace the split vent line and filter. Maybe try a new column.
BR…
Hi!
I still need help yes, please!
- On the machines (GC system and Injector) it just says HP6890 (see photos attached)
- The PC we employ is an old Windows XP running one, that was used to run the GC-FID before we want to control it with the serial…
Hi there, I noticed recently that the ECD back signal on Agilent GC 7890 (using it for trace gas analysis) is oddly spiking (while the FID is a straight, consistent line). It never used to do this. I just recently changed the inlet septum, could this…
Hi,
After a power cut, the batch file I had open on my desktop seems to have become damaged...
On opening the batch, it fails to open... small dialogue pops up >> "failed to open quick scan file. Failed to read binary quick scan file."
Has anyone…
Hi Community
I have an Issue on one of our GC-FIDs 6890N. I have large Peak Tailing, especially on the back of my chromatogramm:
What i already did:
- New Column
- New Septa/liner
- New Gold Plate
- Cleaned Inlet and Detector
- Re…
Any special procedures to prepare for cross-country shipment a 7890B with SS, PP inlets, heated valve oven, and TCD-FID? Also a 7697A with 100-vial tray?
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...