yes, it's the purged 2-way splitter. Bottom is column entry, then detector 1 is FID, detector 2 is qtof. (switching FID and qtof position doesn't change anything)
We had 3.7mx0.15mm to qtof and 1mx0.15mm to FID with constant flow 0.8 ml/min for a 1…
Hello, I need to archive a file but the file do not archive. It appears the message "Last archive operation failed"
How can I know why the archive failed and how can resolve it?
Thank you
Thanks Marty, I was afraid of that.
Too bad really since piecewise is the most conventional kind of multi-level calibration.
I train using the example of a typical pH meter where they still naturally calibrate at pH 4, 7, & 10. Therefore there…
You can swap out cylinders to do it, but that means a lot more tubing, etc. to purge when you want to run. With the EPC unit, you would simply load the appropriate method to use it and the switch is done at the instrument. Much less tubing to purge and…
Hello Community
We have a reproducabiility problem on GC-FID's. We run an alkane standard every day in the morning. Peak shapes are looks good but when i compare the total area of the peaks over the last weeks an month, its very bad, i have a standard…
Hi
How do I remove FID signal from the report for a dual TCD & FID GC, we use just TCD detector to analyses gas samples and this issue appear yesterday.
open lab rev. C01.05
Hi Agilent,
Due to helium shortage, we need to change carrier gas for our GC-FID. Most documentation for Agilent suggests either H2 or N2, and the Chemstation configuration shows those options as well.
We are considering using argon, however, I…
Carbon disulfide is another option for wash solvent when running naphtha or crude oil samples. It's response on FID is low compared to hydrocarbons, so there should be little to no response if some residual is in the syringe.
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...