Hi again Raina,
as I already told you this cannot be done with just one column, especially with the CO2 concentration up to 20% and water included and the necessity to analyze H2. This is an application we normally build an analyzer for. You need at…
Dear All,
We are using NGA analyser as per GPA 2286 method using FID and TCD.
Could you please advice how to apply the bridging to correct the concentration from FID.
When you run startup, does it use the Standard Tune or User Tune? In the new D rev of software (5.X) you can go to Startup/Startup Configuration and just above the Hardware settings table select Configure ignition sequence. For C rev (4.X) click the narrow…
What version of Windows do is it running? Go to the cell next to the logo (Type here to search) and enter winver and select the run app. At top it should say Windows 10, at this time only MassHunter 5.2 is Win11 compatible. 2 lines below Windows 10 will…
Hello taub .
I think it's a corner case issue and you need a support visit from agilent authorized engineer so please request a service visit as its seems that the error is hidden and not straight forward as you mentioned that you changed alot of things…
Hi
I am trying to install the G7201D version of ICP MassHunter on a 1909 Windows 10 laptop.
It goes through the initial process and then errors with a code of 0xe0434352.
Some additional research implies this is a .Net error but a repair install…
Hi Abdul,
From the picture, it appears your FID flame was extinguished. You can put a metal wrench or a mirror at the top of the detector to see if the exhaust contains moisture from the combustion, but a flat baseline at zero output usually means the…
This instrument is used mostly for FID analyses and the second injector is not working. That's the primary reason why the column will be disconnected most of the time. Also to reduce contamination of the ECD, but it sounds like that isn't a huge concern…
Good Day.
I have an issue to my result in tcd. My Sample is TOGA using Fid and tcd. now the issue is the detection of H2, N2 and O2 are late. before 4.2 min. now its 6.2. the column is new.
Hi guys, when I tried to run my sequence in GC-FID, the workstation showed "front injectors not detected", and under my method, the configuration showed no injectors. However, the parameters I entered for injection could be found in the GC (7890A) operation…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...