Hello,
I am not sure exactly what you are doing but to use part of the text in an if you can parse apart the text using string functions or use the like comparison. So your =IF(COUNTIF( A2 ,"*mg*"),"Value if true","Value if false") would be =If(A2…
How many total runs on this system?
8890 and Intuvo: Service Mode, Instrument, Usage
7890: Service Mode , Diagnostics, Instrument Status
6890: Options, Diagnostics, Instrument Status
A 6890/5975 probably has many, many runs on it and passed…
There could be issues with either control signals to the HED power supply or the power supplied to the HED power supply. These electronic issues are down in the depths of the instrument and should be handled by a trained service engineer. Please contact…
A bit late maybe, but you can set the printer within the macro using the MYPRINTER = "name of printer". Use the command before your STARTPRINT command, and then at the end of the macro remove it (REMOVE MYPRINTER), so that it will only be active for the…
Here's a link to the video from this event!
(+) Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table - Follow-up Discussion - Forum - Gas Chromatography - Agilent Community
You should always consider that after re-igniting the lamp, it typically requires 60-90 minutes establishing a stable detector signal.
Based on this it does not always make sense and saves lifetime shutting off the lamp.
Keep constant flow 1.2 ml/min into the MS and do a Pulsed Splitless injection, tips in the help section of the Operating manual. Your system's diffusion high vacuum pump can only handle 2.0 ml/min maximum so do not exceed that ever.
If you have a 30m…
In Manual Tune, PFTBA closed, set the scan range to 10-100, then click on the spectrum scan button. The spectrum will show repeatedly in the middle window to the left at the long red arrow..
Beautiful. Does the spacing change with a different column flow rate? If this is 1.2 ml/min, for example, is it different with only 1.0 ml/min? If it changes and you did the inlet and column maintenance properly, the issue is before those. If it does…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx showing a series of errors after delivery, guide for troubleshooting and resolving temperature-related error.
Background
When an AriaMx is delivered, it could take...
How to Access Manual Tune in GC/MS MassHunter and MSD Productivity ChemStation
Multiple Results
This Information Applies To: MassHunter acquisition software for GC/MS systems and MSD Productivity ChemStation for all Agilent GC/MS systems
Issue
Manual tuning lets you interactively set the MSD parameters, such as lens voltages and tuning masses...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
How to find the AriaMx software and firmware version that you have installed.
Steps to Follow
There are two different ways to find out AriaMx software version:
In the...