James, Thanks again. Actually, at first we had "EPC or detector error” and we tried to clean the detector but with no change. Once the GC says “Ignite, ignite” the error pops out. We tried second module (the refurbished) and at first we were receiving…
Hello !
I interesting gc8890 and gc7890.
In datasheet the gc 7890 writing about posible instal 3 detector maximum, but in datasheet gc 8890 writing about posible 4 detector. I never see 4 detectors are installed simultaneously on one chromatograph…
Hi abtisam, The main reason for this problem you didn't select detector signals. when we don't selecAdd t signal detector we never see baseline chromatogram,to solve this problem from online plot for FID signal Click on change than from Edit signal plot…
Hello,
We just recently got a new tapestation 4150 in our lab, which we're trying to set up. As a part of the setup I rand the full system diagnostics to see if the system is working with the Tapestation Test Tape. Everything runs successfully and the…
Hi wcody, thank you for the reply! It is Windows 10 Pro 64-bit. These 6890 FIDs are new to the lab, Windows 10 pro was what the technicians had installed on the computers when we received them.
There is currently no available solution for working with MassHunter data. If your GC has an FID in addition to a mass spec, you could use OpenLab GC ChemStation to acquire the FID signal data. Then addon G2887BA could be used to analyze the ChemStation…
What are the pros and cons of putting a TCD in series with an MS? I know that it's possible to put a TCD and FID in series but I want MS data, not FID data. I tried teeing off the column between the MS and TCD but all the samples keep going to the MS…
ISH, that is a very good question. Yes, you can. However, you have to be mindful of a few things. For the Deans Switch to operate optimally, the downstream pressure need to be the same on both columns downstream of the Deans switch. The MSD operates under…
Problem: Unable to perform Instrument Configuration for Agilent 1290 LC. The instrument pings at IP address 192.168.254.11 with NO packet loss and connects fine in Agilent Lab Advisor software. Able to perform instrument commands in Lab Advisor.
However…
How to Create a New Database in Spectroscopy Database Administrator (SDA)
Multiple Results
This Information Applies To: Spectroscopy Database Administrator (SDA)
Issue
If the old database is full, or after a specific time interval, it is necessary to create a database in SDA. If you receive a message telling you that the database is full...
Update Database Group Path in Spectroscopy Configuration Manager (SCM)
Multiple Results
This Information Applies To: Agilent Spectroscopy Configuration Manager (SCM)
Issue
It is necessary to add a database to a group path in SCM after creating a new database in Spectroscopy Database Administrator (SDA) . If access to an older database...
How to Access Spectroscopy Database Administrator Software (SDA)
Multiple Results
This Information Applies To: Agilent Spectroscopy Database Administrator Software
Issue
The SDA application can only be accessed by a Windows user who is a member of the Windows Administrators group and Windows SDAAdministrators group.
Steps...
This Information Applies To: AriaMx real-time qPCR system
Issue
The instrument fails to reach the required temperature during a run.
Resolution
Check if the temperature of the environment around the instrument is too low resulting in the instrument...
This Information Applies To : Agilent ELSDs G4260A, G4260B, G4261A, G4621B, G7102A, G7102B
Content :
If the evaporator tube of ELSD becomes contaminated with nonvolatile material resulting in poor chromatography, please use the procedure in this...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
The oil should be replaced at least once every six months, or when the oil color is indicates it needs to be changed . The foreline pump should be checked monthly. This article...
This Information Applies To: Agilent ICP-MS MassHunter versions 4.4 - 4.6 and 5.x.
Issue
After performing an autotune, the batch tune report will not generate or print.
Background
ICP-MS MassHunter uses an application called ICP-MS Data Analysis...
This Information Applies To: Agilent 6400 Series triple quadrupole LC/MS systems equipped with a gate valve
Issue
Installing the Ion Transfer Capillary after cleaning or replacement in Agilent LC/MS instruments with a gate valve.
Required Items...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the procedure on how to quantify uncalibrated compounds in OpenLab CDS 2.x. using reference compounds in the processing method compound table.
Background
Uncalibrated...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the procedure on how to quantify the uncalibrated compounds in OpenLab CDS 2.x when the analytical method requires a fixed response factor.
Background
Uncalibrated...