I am operating the MPAES 4210 with the Agilent 4107 Nitrogen Generator. I have run the Gas Test (Plasma Off) and everything passes. When I run the Plasma Ignition Test, the plasma ignites (passed), but after 20-30 seconds, the plasma shuts off. An error…
7890A GC/5975 MS/E.02.02 SP2
Sequence is stopping constantly with the following log book message: "The run was stopped by the instrument's stop button or stop input. The GC Failed to Start."
Found that exact error in the KBR - " Known Problem Report…
I apologize because this is a very blind question- New IT guy to the company and previous didn't have good documentation on this application.
I have a user who is getting the attached error whenever they try and open Sequence Manager or open Bioconfirm…
New FID Jet!
The latest FID jet is intended for use in 6890/7890/8890/8860/8850/9000 GC models
The legacy jets will not work in the 8890/8850/8860/9000 GC models
The new jet makes installing the column seamless with a conical shape to direct the…
In detail, you can follow below link to resolve this type of problem.
https://community.agilent.com/technical/gc/w/wiki/7889/troubleshooting-an-fid-not-igniting
Hopefully, problem will solve..
I'm currently encountering a challenging issue with MassHunter Acquisition Software that has significantly hindered my workflow. I am hoping to leverage the community's expertise to find an effective resolution.
Switching from MRM to dMRM Settings Error…
Hello
I am having a hard time trying to figure out how to only display one FID signal on a report from a dual injector GC system in OpenLAB 2.4. The calibration that was run used the dual injector setting, but when we were running test samples we only…
This 6890 is code named FIDDY because of its dual Flame Ionization Detectors. The SF FBI donated it to UC Davis Chemistry over 10 yrs ago. It is used to teach Chemistry majors gas chromatography and replaced an old Varian 3800 with a chart recorder!
System: The GC is an 8890 with TCD in series of two FIDs in parallel (switched via valve). FID 1 has methanizer while FID 2 doesn't.
Had to put the system on standby for 3 weeks over Christmas so kept carrier flowing through the system with all heated…
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...
This Information Applies To: Agilent 7890/7820 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent LC pumps
Issue:
Stuck or obstructed check valves (Active Inlet Valve (AIV), Passive Inlet Valve (PIV), Outlet Ball Valve (OBV)) can cause issues such as no-flow or no-pressure, moderate to strong drops in pressure...
This Information Applies To: Agilent 1260 Infinity II multisampler, 1290 Infinity II multisampler, 1260 Infinity II SFC multisampler, and 1260 Infinity II bio-Inert multisampler
Issue
The needle bends while moving to the wash port or showing one...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the step-by-step instruction on how to overlay chromatograms for OpenLab CDS 2.x
Steps to Follow
Load data from result sets or single samples. See Load or add...
This Information Applies To: Agilent Lab Advisor Software, Agilent Multicolumn Thermostat
Issue:
Agilent Lab Advisor is a great tool to diagnose the issue of your HPLC. Running the tests that are relevant to your specific issue in the Service &...
This Information Applies To: Agilent OpenLab CDS (ver 2.x)
Content:
The following procedure shows how to review completed injections in a running sequence in OpenLab CDS (ver 2.x).
Steps to Follow:
Select the sequence from the Run Queue...