Hello
I recommend to replace X-belt.
P/N 5410047500 Belt timing – 880 mm
When initializing if the belt tension is not enough, It could be failed.
Please check it.
Thanks! To add, I just ran the software verification tool and the MassHunter GCMSAcq_base.xml report failed. File Report Summary
Missing files or invalid files found:
Invalid Files :1
No system file difference found
Invalid Files …
When running a calibration on the GCMS the internal standard increases the entire time for all of our standards. It goes from around 1.9 million for the bottom of the calibration to 3.2 million. Recent things that we have done that should help eliminate…
Hello Lars, Thanks for your reply. Unfortunately, there is no flow meter meter installed. So you are saying that, in your case without stopping gas flow before GC injection, you are only getting 1-2% deviation in FID response? If possible could you explain…
Morning, You are correct. I am running OpenLab CDS ChemStation. Rev code = C.01.04 [35]. Intelligent Reporting product version A.01.04.122. The system suitability issue is that I'm only getting the TCD satistical results. The FID result are not printing…
Hi there! We have a Cary 60. We are doing preventive maintenance, but the noise test fails and it took up to three or four times to get a successful result. What can we do to improve this and get a passed result the first time?
I am trying to quantify ethyl lactate in ethanol 20% (remainder water). When I run multiple injections, the RSD is 6-8% for the ethyl lactate peak. The ethyl lactate standard should be 0.2% v/v. We typically test samples that are 95-100% ethanol and use…
I have a G4226A autosampler with a recurring error message. Movement of needle into seat failed [EE 4714, 3204]
This error started after the autosampler had been repaired by a field engineer. The main board had to be replaced; the computer was unable…
Hello, we were not able to tune the instrument at all. There was so much noise at low mass that it fails the initial quad coarse mass calibration. We think it is PEG contamination, possibly also PPG, but a number of masses correspond with sodiated PEG…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...