Hi This morning the check Tune failed. After adjusting MS1, the tune passed with warnings. Then I decided to autotune. It went through many of the steps until "Enhanced" failed. I am not sure what this step is. Not easy to find any documentation. Can…
We have a 7890B that was configured with an MSD but is being reconfigured for a different analysis. It is now running an FID/TCD method, and the aux detector has been disconnected and unconfigured. The MS/Aux Det button on the GC keyboard says no aux…
Hello everyone
I have 3 error messages from the Agilent infinity ii 1260 SFC Multi sampler:
1- Metering device Movement Failed ( EE25444.0) 2- Taking needle From park station failed ( EE25105.201 ) 3- Axis did not reach its target position in time…
When Air gap is 0.2 and the flow rate is 2.1 ml/min then the peak area found 287 by FID but when the air gap is 0 and flow rate is 1.47 ml/min then the area reduced to 141. Where analysis performed by Autosampler.
Hi, I have the same problem as well. We are using LC 1220 Infinity series. We tried flushing the system with isopropanol for 10 minutes just in case the bubbles are present. However, this does not solve the problem. The pump failed to get ready within…
I think we do this at my lab but not with a valve. We use a plot column and anayze headspace above a water sample. We test for methane ethane ethene and propane useing an FID. The integrated gastight syringe with a valve in it from Fisher helps. We use…
Using OpenLab EZChrom A.04.1.0.0 with a 6890N GC-FID this error occurs
The IS dept have looked into this and have commented that the systems log mentions that the instance has reached its maximum size of 32MB. We have been running the same system…
Hello everyone, I would like you to help me with a genesys 30 spectrophotometer, I have a problem that says: * Zero-Order search failed
psdt: I have already changed the focus for a halogen one but it only reads from 500 nm but at 325nm it does not read…
Hi. I am having more issues with my ancient 1100 stack. I am getting an EMPV initialization failed error. As I have done some other research it says that the bar should be around 20 bar and then you can do x, y, and z to fix it. However my bar is less…
I'm trying to use the DA Reprocessor (B.08.00) to process TOF data as a batch on a Windows workstation. If there are too many features, the DA Reprocessor stops with the following error in the log: Failed to run worklist Qual: The Operation has time out…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...