Hello dexter91, I need to have the column configuration from your system in order to give you a proper answer: are you using only 1 column with a splitter at the end to split it to the MS and the FID or you have 2 columns configured, 1 for each detector…
Dear Team,
Is it OK to use 8860 system for USP467, residual solvents analysis ? Literature that is available is mainly on 8890 but 8860 can also be used ? Agilent do have a blood alcohol analysis app note on 8860 with HS, 1 SSL, a Tee connection, 2…
In our company we are using a GC-FID Agilent technologies 7820A connected to a Headspace 7697A from Agilent also,
and we are not able to transfer some methods into our system when the carrier gas is Nitrogen.
Our team is in charge of the Method transfers…
I looked around but failed to find anything useful. Is there somehow possible to export results/data from SureMass-deconvolution/ID in Unknowns Analysis for further processing and or statistical analysis (besides .CEF-format)?
We currently use Agilent 7890A GC with S/SL injector and FID detector using a capillary column for the analysis of crude oil composition upto C35. The remaining compounds will be reported as C36+. The temperature program is from 30 Deg to 325 Deg, We…
After most MSD maintenance (filament change/switch, source cleaning, etc...) I seem to have an issue with the baseline dropping in series (offset pattern) for up to 2 weeks afterwards. I'm new to this machine, but I'm in the process of slowly changing…
Hello,
Please mention the instrument you are trying to work with.
Please see the following for GC:
GC Signal Conversion Factors
Use to convert to display scale units
Use to convert to unscaled…
Hello, thanks for update (I wonder if my memories were incorrect,,, Your question is classed "difficult" ...... Let me start easier one! The visible lamp is not required replacing. It seems working without error. that is typical "bulb" , if id is out…
Hi there, I've recently started using a GCMS (7890A + 5975C MSD). The tune has failed and the GC shows a flat line at 0.5 whenever a sample is run. I've attached all relevant photographs I could think of, including the GC spectra where it all stopped…
I've recently been running into some problems with performing SureMass conversion of data collected on a 6546 LC-QTOF. I'm collecting both profile and centroid MS data using the default data storage thresholds.
Initially, I was running SureMass conversion…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...