After a failed methamphetamine quantitation, it was noticed that the methamphetamine peak shape on our GC/FID instruments has been consistently poor or deteriorating through out a run. This has been happening on both of our GC/FID instruments (all 3 columns…
It looks like theres a problem with the back inlet/back autosampler - the gc does not recognize it anymore - but it seems to be defined within the method, meaning it has a inlet temperature ect.
Did you change something regarding the back inlet? or…
We have OpenLab 2.1 (with content manger) running our GC and LC systems. We have successfully been running 2 x GC and 6 x LC systems however this morning on two of the systems we can see the following error:
Acquisition
Failed to connect to the…
Hello, Just to add on to dnprulz 's reply, the expression that he provided will work in OpenLab Custom Calculator and should perform what you are looking to do. However, if you want the pass/fail logic to be set on the report template then you will want…
Hi all,
I have a 6890A GC with a FID. We recently acquired the instrument and I have been running standards up to test methods. I have been getting signals that seem suspiciously low.
I am injecting Matreya Bacterial CP FAME mix (C11-C20 methyl esters…
Hi, I ran my batches with GC-FID under MassHunter Quant, but I cannot generate any reports. The error popped up during generating which is "Error: 'QuantDataProvider' object has no attribute 'FormatDateTime'." Has anybody faced with this issue to help…
Update: I checked filament and looks fine. Weird when switching from EI to CI source the tune fails 3x in a row and then passes every time after that. This happened twice after switching source. The tunes that pass though do not seem like everything is…
Hi
Either there is leak or loop is not filling properly with sample for low area.
And for too hot transferline, may be PC board or sensor is malfunctioning or faulty of headspace.
You can change column or trim the column from inlet and detector…
Hi Tom, we were told to upgrade to version 10.1 and it solved this issue. However, we found different strange behavior of manual integration. General integrator sometimes fail to integrate peak while manually integrating. What I still don't understand…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...