Once the lamp got ignited the light arc between anode and cathode has been sustained.
The referring anode voltage typically stabilizes after a certain time and can be heavily influenced by environmental conditions.
Fluctuations in the anode voltage…
Thank you Kbusch.
Is there any videos that can show me how to move needle arm out of the seat. I tried to go through Lab Advisor but the arm does not go to maintenance mode. Lab Advisor timed out and failed to connect to LC. I shut down the sampler…
Your controller is going in Auto Tune
Autotuning condition is shown when the controller has delivered an output power level higher than a typical value, but the pump is still not reaching full speed value.
It does not matter if it is a normal start…
Dear all,
we have not measured many samples, only some organic samples. Could someone please explain, what cause the RF coils change the color like this? Does it affect the plasma ignition? How to clean it properly?
Is it correct, I take the coils…
Hi All,
I am experiencing a configuration issue with a new Thermo Fluorescence Detector installation on a 1200 series LC with OpenLab CDS 2.5. After installing the SII 1.2 Software for the FLD, I try to configure the FLD with Chromeleon, however I am…
Riddle me this. We've encountered a rather strange phenomena when optimising MRM transitions on a Agilent Ultivo TQ. The MS does not have any issues in generating the precursor ion for example 897.5 (216V fragmentor) but fail to generate a product ion…
Hello collrube ,
No such thing as a dumb question
Just so I can understand the question better, do you mean that you used to have a 5890 GC FID system, and you replaced that with an 8890 GC FID system? Or do you mean that your FID on the 5890…
May I ask? Did you take an official FLD training? Working on the innards of an FLD usually is for trained staff only. Many things can go wrong here, e.g. replacing the lamp is much different to replacing the lamp on a UV detector. One can screw up the…
Hello! I followed this tutorial part D Linked Dual GC Signals 1 aliquot /cfs-file/__key/communityserver-discussions-components-files/152/0020.DualTow7890EnvMH.pdf to sample 1 aliquot through both the front and back autosamplers, both columns, to both…
Hello SimonHarries ,
The only time I have heard an FID trying to re-light itself is when the baseline of the FID dropped below the Lit Offset value.
What is your baseline at (in pA) when the FID is lit, but not running sample? And what is your lit…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...