The Digest of upcoming webinars has been updated as of April 2.
In April, you don't want to miss the GC Live Event, Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table on April 11!
Check out the new Agilent Community Group, GPC…
The slope of the second plateau in the leak test for the quat pump of our Agilent 1100 fails. We are getting a negative slope of -2.18. Pressure and slope for the first plateau passed. Pressure for second plateau passed but the slope was negative giving…
What version of WinUV do you have? We were delivered WinUV 5.1.3 with .1042 (Part 11 security module).
The system was built with a tutorial in Adobe Flash but unfortunately for all of us, Flash was discontinued worldwide for security reasons. This meant…
Hi,
I suggest to run an auto-tune, then you will have a checktune report at the end of a sucessful auto-tune. If the auto-tune fails for the same reason you have mentioned and gives the same error message and you are sure the bottle not empty and nebulizer…
Basically you must create standard calibration level with level name as you wish, and u will not use this level for calibration, but only for comparing your QC in batch table with this "calibration level".
Hi Sabbas, The "Peaks and Valleys" option can be used to label both peaks and valleys on the same spectrum.
Right-click on any dataplot and click "Peak Labels", and under "Peak Type", select "Peaks and Valleys". If the "Threshold" value is set up according…
This is a compilation of some of the most useful GPC/SEC System resources, including recommended column and standards, software packages, theory and operation, user manuals and troubleshooting guides.
GPC and SEC Columns & Standards for Polymer & Plastic…
Hi martin.adams , you are exactly right, the peak width is small, therefore it is not giving the final S/N value. When I manually integrated the peak by increasing the peak width, it gave the value. It seems i need to fix the time range for the baseline…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...