The file is a pre-set qPCR program to run a plate filled with water used to test the basic raw fluorescence signal of AriaMx Optical modules.
File required for Performing a Background Calibration
The GC cycle time should be the time from injection until the GC is ready to run again. This includes the analysis run, cool down, and equilibration. Based on the times you listed, it would be roughly 40 minutes. It may be worth timing to make sure. The…
Hi howard_sanford, my apologies for a slow response, but thank you very much for the help and advice. I was able to get the filter for Cal and CC to work, and I appreciate the discussion of my larger problem. I think I'm probably several (many) steps…
Hello, thank you for your help. I had tried loading different processing methods but I didn't realize the results were not linked to any method. It turns out the result files were read-only and could not be linked to any method. I moved the result files…
The peaks look similar, essentially the same sensitivity. I'd look at the background on your older runs and the background now. It could be that most of the previous background was one, two, a few, ions and they're gone now. Was that small but still noticeable…
That is one failure mode of Platinum Resistance Thermometers. It can happen one degree to the next higher degree. The heater/sensor must be replaced, part number G1099-60107.
See also: (+) AUX 2 heater fault - Forum - GC/MS - Agilent Community
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...