Dear Community
I am using a GC/FID from Agilent with Openlab CDS. The GC/FID has to columns (front and back) which gives a slightly different retention time for the same substance. I use both lines, one for the measurement and the other for the control…
I don't think it would have a problem as long as you're not trying to connect with both software platforms at the same time. I've seen other customers do similar things (GCMS/FID, using MSD Chemstation for MSD work and GC Chemstation for FID work).
Are there electronic checks that can check to make sure a filament isn't failing because of an electronic issue? We had a filament die, which isn't too surprising considering it was nearly ten years old (teaching institution, the instrument sees periodic…
Hello,
For awhile now, I've been having issues with my resolution axis "passing" for masses 25 and 26 in no gas mode. I have done many cleanings and new tuning solutions. Can anyone explain what is causing this continual failing and what I could do…
Hello Agilent community,
I have recently been 'Recovery Test in GMP' of Openlab 3.4 (Build 3.4.0.242) in a standalone environment using the Windows Hyper-V feature.
During the testing, I found the following two issues
First, a warning message…
I work in a small, environmental lab. We test aluminum levels in serum using ICP-MS. We can run batches of 250 samples at a time. We dilute 500 microliters of serum to 5 ml using 0.2% HNO3. We calibrate using 1, 5, 10, and 20 ppb Aluminum std. At the…
Good morning,
We have an Agilent 7820A GC-FID equipped with a G4567A autosampler.
In the middle of a sequence, the system gave the following errors:
ALS Failure State: Preparing Samples
ALS Failure Code 945 : Autoinjector back tower plunger…
Hello, Just to add on to dnprulz 's reply, the expression that he provided will work in OpenLab Custom Calculator and should perform what you are looking to do. However, if you want the pass/fail logic to be set on the report template then you will want…
The Digest of upcoming webinars has been updated as of December 13.
Notable additions include:
Atomic (4)
GC & GCMS (9)
Vacuum Solutions Series (1)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from…
We have OpenLab 2.1 (with content manger) running our GC and LC systems. We have successfully been running 2 x GC and 6 x LC systems however this morning on two of the systems we can see the following error:
Acquisition
Failed to connect to the…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...