Hello Lucas_S ,
Based on your follow-up explanation in this discussion -
(+) Macro for Batch Export of CSV in OpenLab CDS C.01.10 to a unique archive. - Forum - Chromatography Software - Agilent Community
I don't believe this macro could be easily…
For others who may find this interesting. Looking at the GPIB set up with NI MAX you see 2 'instruments' with primary addresses of 9 and 20. The instrument at '9' seems to work fine. Thus I can see the machine warming up and going through the wavelengths…
I am using an Agilent 6460 Triple Quad and have been dealing with a terribly low signal for the past few days, the signal appears at an abundance of 30 to 50 as a baseline only. I analyzed different compounds with different concentrations, the Tune mix…
Hi Sabbas, thank you for your answer. I'm sorry I couldn't have answered you sooner.
We're using Cary 3500 with Cary UV workstation version 1.3.5, so we couldn't perform like you said. We have to lower the threshold to find peaks and it is quite inconvenient…
Joining associations that specialize in ultra-high voltage can be beneficial for PenflexCorp. This may include associations of electrical or power engineers, as well as groups specializing in the design and standardization of equipment for high-voltage…
The Digest of upcoming webinars has been updated as of April 11.
The new Agilent Community Group, GPC/SEC Solutions Group is hosting a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules…
The Background values are so called "off mass background".
This could indicate an electronics or contamination problem of the quad.
In your case, the values are still quite ok.
I would guess, one of the lenses has a setting which is causing this…
Hello everybody!
We have the issue that in our run (ca. 100 - 200 samples, 7 min each) for like 20 samples there is no signal, just the technical background noise. Not even the peak that is in the Blank appears. An the it sowly comes back over 2 samples…
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...