Typical communication with Agilent activities:
Order Acknowledgement email.
Order confirmation (Thank You) email. Customer can access My Orders Account to track the status of the order.
Ship notification email.
Communications from Consumables…
Hello
I need to do an LC/MSMS method for quantification on a compound that doesn't ionize into [M+H]+ (barely observed) but only into [M-H2O+H]+
Is there a problem with doing MS/MS on a [M-H2O+H]+ parent ion ?
(PS: negative ionization is not an…
Hi again Raina,
as I already told you this cannot be done with just one column, especially with the CO2 concentration up to 20% and water included and the necessity to analyze H2. This is an application we normally build an analyzer for. You need at…
The Digest of upcoming webinars has been updated as of June 5.
In June, you don't want to miss the GC Live Event, GC Live is Back in June with the Next Big Little Thing in GC: The New 8850 GC System on June 6!
Check Out:
Intelligent Analysis of…
Operating like this puts sub-optimal flow into the GCMS ion source of more than 2 ml/min. Please make sure that you have a system with a turbomolecular high vacuum pump and not a diffusion pump as 2 ml/min exceeds the maximum allowable flow into a diffusion…
Exciting news in the world of FTIR spectroscopy!
Agilent has just released MicroLab 5.8 , MicroLab Pharma 5.8 , and MicroLab Expert 1.3 —the software that powers the Cary 630 FTIR spectrometer and Agilent’s handheld and mobile FTIR systems . MicroLab…
Hi Margot,
It may well be that the column performance has deteriorated so much within the 7 months that the EasiVial standards are measured with poorer PDI values. The column performance can be tested with regular plate count determinations. It is a…
Hi sojeong,
every test report, delivered with aour columns, contains multiple specifications, but they are all measured with specialized systems and software. That means you might not be able to reproduce them identically. BTW for plate count you also…
Hi, I cannot configure the column compartment (CC) as it came integrated with the vial sampler on LC1290. We have the G7129B model for the integrated vial sampler and CC. I tried adding the column compartment details from the instrument configuration…
When the tuning is done at 3200 (+) everything is fine. When I change it to tune at 1700 (+) the masses are reasonably accurate. After it gets to the third mass (620) it appears that the entire spectrum shifts by about 1.5 AMU and the tuning fails. There…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...