Hello,
I am not sure which Agilent software (CDS 2.x , Chemstation, EZChrom) you are using, but most customers use third party software for simulated distillation and other RT vs BP petrochemical calculations. If your need is simpler, you could do…
Thanks a lot.
Also I found that not all parameters (column width, labels) can't be changed in report designer. I changed them in xml template manually. Is there any description of functions and variables to change some report layout?
In the earlier 2 posts, I have discussed about 1. The merits of automated sampling and 2. Validation of automated dissolution system . Thank you for giving our team warm response for these blogs. We received many queries regarding automated sampling on…
Hi Lisandro,
if your analysis looks fine, go for it. The mentioned increase in off-mass background can affect your signals (not predictable) on other masses, as it is electrical noise.
BR Chris
Hi,
rinsing with a higher concentration of HNO3 sounds like a plan
you could try to sonicate the T-Piece where the istd is connected. Often this is a source for contamination. Anyway the Pb is not a problem in this low concentration. And your main…
That video is a bit hard to see. There's no visual evidence of overheating nor staining on the rest of the analyzer/quad radiator. The factory gold is not a separate applied foil. That needs further investigation. I would recommend contacting Agilent…
Hello,
I am not entirely clear on what you are doing as well. Below is an example of how I would do a % recovery from an existing standard injection in the result set. The calculation would pull the theoretical value (Compund_CalibrationAmount) from…
Hi JONHY , thanks for your question.
I’ve used an online tool to translate your post. English is the official language of the Agilent Community, and the platform does not support translating a post from local language to English. You can view pages…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...