I am operating the MPAES 4210 with the Agilent 4107 Nitrogen Generator. I have run the Gas Test (Plasma Off) and everything passes. When I run the Plasma Ignition Test, the plasma ignites (passed), but after 20-30 seconds, the plasma shuts off. An error…
7890A GC/5975 MS/E.02.02 SP2
Sequence is stopping constantly with the following log book message: "The run was stopped by the instrument's stop button or stop input. The GC Failed to Start."
Found that exact error in the KBR - " Known Problem Report…
Hello all, we have acquired a 120V 7820 ex-US (2011 build w. UEPC´s for 2x FID) and converted to our local 230V by swapping heater shroud & AC board. After that it initially would not heat higher than 280C but bail out with a thermal shutdown. Fan was…
I apologize because this is a very blind question- New IT guy to the company and previous didn't have good documentation on this application.
I have a user who is getting the attached error whenever they try and open Sequence Manager or open Bioconfirm…
Hello
I am having a hard time trying to figure out how to only display one FID signal on a report from a dual injector GC system in OpenLAB 2.4. The calibration that was run used the dual injector setting, but when we were running test samples we only…
New FID Jet!
The latest FID jet is intended for use in 6890/7890/8890/8860/8850/9000 GC models
The legacy jets will not work in the 8890/8850/8860/9000 GC models
The new jet makes installing the column seamless with a conical shape to direct the…
This 6890 is code named FIDDY because of its dual Flame Ionization Detectors. The SF FBI donated it to UC Davis Chemistry over 10 yrs ago. It is used to teach Chemistry majors gas chromatography and replaced an old Varian 3800 with a chart recorder!
I'm currently encountering a challenging issue with MassHunter Acquisition Software that has significantly hindered my workflow. I am hoping to leverage the community's expertise to find an effective resolution.
Switching from MRM to dMRM Settings Error…
System: The GC is an 8890 with TCD in series of two FIDs in parallel (switched via valve). FID 1 has methanizer while FID 2 doesn't.
Had to put the system on standby for 3 weeks over Christmas so kept carrier flowing through the system with all heated…
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...