Thanks for advising, do other errors show up in the logbook?
Please watch the movement of the sampler arm during initialisation:
- Is it shaky or jittery? If yes, turn off module and clean transport rods using IPA & lint free cloth.
- Which position…
Hello, I will take a picture when I go back to the lab tomorrow. I must also let you know that we were able to extract an old method from the GC. This method had been downloaded into the GC from before everything crashed. When using this method, the GC…
Hi I had a question about GC MS Split (gc to FID/MS). I have a thermo splitter that has no auxillary flow to counteract the ms vaccuum, but want to change out the capillaries that come recommended with the splitter. The recommended capillary dimensions…
Hello,
We have been having issues with our ICP MS performance and tune reports. Both have been failing with low counts. We have changed the peri-pump tubing, remade all standards, remade the tune solution, replaced the torch, and cleaned the cones…
Hello isoterma, Maybe try a new jet ? Cleaning doesn't always get rid of restriction in the jet. I see your supply is supplying both detectors but if the pressure is on the lower side of acceptable raising the pressure may cure the issue. For the 6890…
Hello, I have an issue when I try to install OpenLab CDS EZChrom Version A.04.07 The plan is to install EZChrom on a Citrix to allow the user to retrieve files from ECM for review or reintegration. I start the installation and select the Installation…
Csiquet_flex2000 my guess for your 4 signal sources the Save check box is unchecked, so you don't see them as an online signal during acquisition nor as a saved raw data file. The Signal settings under the GC Parameters is only for GC based detectors…
Hi Jennifer We had an GC-MS issue in the past where the rough pump was starting to fail and as a result kept drawing too much current, causing some of the fuses to fail. We also had an issue with a rough pump (on a LC-MS) which was blowing fuses when…
Hi ronin, It sounds like you have a 7694A with the newer headspace mainboard (7694B) that didn't have the visible changeable battery. In this case the ability of the board to retain stored parameters has failed due to this battery failing. The only fix…
Hello mr.white, You can do this with a sequence summary report template: Use 'Multi Signal Plot Overlaid' as you've done already; in the properties, the signals need to be overlaid. You may group by signal e.g. FID Front signal/ FID Back signal or, if…
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Can I use reaction volumes larger than 30 μL on the AriaMx?
Resolution
There is no problem with using higher reaction volumes, but the instrument performance can only be...
This Information Applies To: Agilent OpenLab CDS software version 2.3 or higher.
Issue
Chromatogram gridlines can help users to get a better understanding of the scale of the peaks. However, in some cases, the gridlines are not desired, such as...
How to Reset the Agilent GC/MSD Tune File to Default Values
Multiple Results
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software
Issue
If there is a problem with the current tuning parameters and a need to tune from the default parameters, see the following procedure to reset the EI tune file (atune...
This Information Applies To: Agilent OpenLab CDS (version 2.x)
Contents:
In the following procedure, you will find steps to create a multipoint ESTD calibration method with OpenLab CDS 2.X.
Steps to follow:
1. Load the Data
a. From Data...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Chromatographic peak integration is a critical part of accurate and reproducible quantitative data analysis. The integrator type and the integration parameters...
This Information Applies To: Agilent 6200/6400/6500 Series LC/MS Systems
Issue
Instructions on how to fill the calibrant bottle on 6200/6400/6500 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal.
Issue:
Installing the Ion Transfer Capillary after cleaning or replacement. For instructions for installing an ion capillary...
This Information Applies To: AriaMx Real-time PCR System
Issue
The saturation level is unique for each optical module after the offset of calibration factor and background calibration. The FAM, ROX, HEX, CY3 & CY5 optical modules will saturate at...
This Information Applies To: Agilent LC Systems
Issue
While it is possible to combine modules from different HPLC series such as 1100, 1200, 1260 or 1290 series to create a functioning LC system, there are some important topics to consider.
...
Fixes for the "RPC Server Unavailable" Error
Multiple Results
This Information Applies To: Agilent OpenLab CDS
Issue
When launching the instrument Acquisition screen/instrument session, there is an "RPC Server Unavailable" error.
Resolution
Accessing the Services App (Windows)
There are two ways to...