Hi, Using one and the same column for different applications is possible, as long both solvents are permitted (column user manual e.g.).
The column should always be flushed very slowly from solvent A to B (0.1 mL/min). At least 5 times the column volume…
Hi Marty,
Thanks for taking the time to respond. I saved the data to a file and then printed the file and it was properly formatted. I think that there is an issue with printing to paper from the method. Since this is a long unsupported CS revision…
Hi Abbey
Thanks for the info!
So far we have only been running this on various forms of olive oil. But the waves in the baseline remain regardless of MOAH contant. I have run samples that were analyzed by outside labs (with COA) that contain 0ppm…
From a quick google search, it appears that hydroquinone may be detectable through LC/MS (ESI) in both positive and negative mode. It forms a protonated molecule ([M+H]+) at m/z 111 in positive mode and two ions at m/z 108 and 109 in negative mode.
…
奔跑的小短腿 , While an LC/MS system may operate in both positive and negative ion polarity modes, it will switch between the two polarities based on the user input in the acquisition software. It is not possible to acquire in both polarities simultaneously…
Hi Vincenzo,
Thank you for your answer. We have the CFR environment. WinUV 5.1.3.1042. (1042 indicates Part11).
I’ve looked for method files for the following apps; Advanced Reads which are .MAB, Concentration .MCN, Scan .MSW, and Simple Reads .MSR…
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system run ends prematurely and the following error appears in the logbook: Run aborted on port x. Instrument error occurred on port x, Unusual...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The Agilent 2100 Bioanalyzer system electropherograms in the Agilent 2100 Expert software have a wavy, uneven baseline ( Figure 1 ).
Figure 1. Wavy, uneven baseline on Bioanalyzer...
This Information Applies To: Agilent AriaMx systems.
Issue
When IP addresses of an AriaMx instrument are reassigned, it will appear under the new and the previous IP address in the AriaMx Instrument Explorer. This situation can be prevented using...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Sometimes, for support purposes, it is necessary to send the diagnostic test result file to Agilent support representatives.
This file contains detailed information about the...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx Real-Time PCR software
Issue
How to change the discovery protocol port in the AriaMx software.
Steps to Follow
The AriaMx software uses the UDP Broadcast protocol for...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
The instrument diagnostic tests should be run whenever it is suspected that there could be a fault with the instrument hardware.
Background
The instrument diagnostics consist...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Error 45 is displayed on the AriaMx instrument touch screen.
Background
Error 45 is shown when the temperature recorded by one or more thermistors is outside the expected...