Hi Brenda, Whats the total flow setting on the inlet set at? If the total flow is set high because of a high split can be one reason. I suspect this is more of a hardware fault like a blocked split line or a split valve problem. Shutdown #4 This message…
James, Thanks again. Actually, at first we had "EPC or detector error” and we tried to clean the detector but with no change. Once the GC says “Ignite, ignite” the error pops out. We tried second module (the refurbished) and at first we were receiving…
Hydrogen (H2) is the simplest and most abundant element in the universe. Since, it only occurs naturally on Earth when combined with other elements it must be produced from other sources. It can be produced without a carbon footprint from variety of sources…
Hi abtisam, The main reason for this problem you didn't select detector signals. when we don't selecAdd t signal detector we never see baseline chromatogram,to solve this problem from online plot for FID signal Click on change than from Edit signal plot…
Hello Maybe this question be out-of-date for the current time but I will be appreciate for everyone that can help me. I have few Varian CP-3800 GC in our Lab, unfortunately some of them failed to operate because of electrical board part. I requested these…
Hi wcody, thank you for the reply! It is Windows 10 Pro 64-bit. These 6890 FIDs are new to the lab, Windows 10 pro was what the technicians had installed on the computers when we received them.
There is currently no available solution for working with MassHunter data. If your GC has an FID in addition to a mass spec, you could use OpenLab GC ChemStation to acquire the FID signal data. Then addon G2887BA could be used to analyze the ChemStation…
Hello,
We just recently got a new tapestation 4150 in our lab, which we're trying to set up. As a part of the setup I rand the full system diagnostics to see if the system is working with the Tapestation Test Tape. Everything runs successfully and the…
What are the pros and cons of putting a TCD in series with an MS? I know that it's possible to put a TCD and FID in series but I want MS data, not FID data. I tried teeing off the column between the MS and TCD but all the samples keep going to the MS…
ISH, that is a very good question. Yes, you can. However, you have to be mindful of a few things. For the Deans Switch to operate optimally, the downstream pressure need to be the same on both columns downstream of the Deans switch. The MSD operates under…
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...