I am using OpenLab Chemstation C.01.10 on an 8890 with dual FIDs. I was trained on HP's version of Chemstation that reported both detector quant amounts in one row for precision purposes. It made it 10x easier to review data and confirm sample concentrations…
Thank you for the help so far. I was able to solve the problem on my results table by using the "left outer join" function.
However, the report will not print the individual peak chromatograms for the target ion or qualifiers if there was no peak detected…
We suddenly lost power during sample injection, when the power back, the autosampler got needle lock fail error message and fail to go back to needle seat, anybody could help? we did a cold start but not work.
Hi vitiin96,
this is very generic and any book on GC troubleshooting or the videos on the Agilent website could help. For the 7890 there is a troubleshooting manual available.
Good practice in GC is when you get a (new) column, you have an own suitability…
Hi Juliana
Yes, most likely the capacitors and/or the RF Tube. However, you can try to reduce the run power to 1.1Kw in the default ignition table. You may then be able to run for a few weeks with this reduced power level. You will need to reduce the…
Using the Agilent 7890A. Column installed with no leaks detected. Both the front and back detector are set to 300°C, gas Flow Rates - Hydrogen: 45mL/min, Air 450mL/min and He 1.0mL/min. The split flow is 80mL/min. Following initial start up the front…
I have started using GC-FID (Agilent 8890) since March for the first time. We are trying to measure the methane. I was trying to make a standard surve, so I injected 1000 ppm methane standard at first. Just to let you guys know no samples has been run…
Hello Everyone,
I am using 7820A GC coupled with 5977B Mass Spec. After use I close the He tank and later on I get 2 messages - 'Front inlet flow shutdown' and 'Front inlet pressure shutdown'. I restarted the software but it fails to load any GC method…
Varian 710 oes, nebulization is ok, fog in the chamber is omogeneous, tubing, nebulizer, torch, cone cleaned and alligned.
Work fine till 2 weeks ago, after i've experienced this: fail to execute wavelenght calibration end torch allign, No response…
Hello, we are setting up a seahorse assay for a immunology master class. We want to measure the glycolytic rate in human PBMCs or purified human CD4 T cells activated vs non activated. We fail to see any difference. Has anyone done this kind of assay…
This Information Applies To: Agilent 4200, 4150 and 2200 TapeStation.
Issue
Is it possible to analyze single stranded DNA (ssDNA) on the TapeStation? Which kit is the most suitable for analysis of ssDNA?
Resolution
Agilent does not offer any...
This Information Applies To: Agilent 4200 and 4150 TapeStation systems
Issue
How to Run the software installation verification on 4200 and 4150 TapeStation systems.
Background
The 4150 TapeStation model G2992A and 4200 TapeStation model G2991B...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, and Femto Pulse
Issue
Perform a capillary alignment when a new array is installed in your Agilent Parallel Capillary Electrophoresis instrument. An alignment may also be performed...
This Information Applies To: Agilent 4200 and 4150 TapeStation
Issue
Are the Agilent DNA and RNA ScreenTape assays denaturing?
Resolution
The DNA ScreenTape assays in the TapeStation portfolio are not denaturing. Only the RNA and High Sensitivity...
This Information Applies To: Agilent LC pumps with manual purge valve.
Issue
A good practice before using a system is to purge the system to remove air. This is done by observing the clear tubing from the solvent bottle as well as the waste line...
This Information Applies To: ICP-MS MassHunter 4.x and 5.x
Issue
Unable to open a batch in offline data analysis, or the batch is empty.
If the ICP-MS MassHunter software closes unexpectedly, there is a power outage, or the ICP-MS and computer...
This Information Applies To: Agilent OpenLab CDS versions 2.4 or higher.
Issue
How to preview result files using various Report Templates in OpenLab CDS versions 2.4 or higher.
Requirements
The user has the result set loaded in OpenLab CDS...
This Information Applies To: ICP-MS MassHunter with Spectroscopy Database Administrator (SDA) and Protect Local Data ON.
Issue
An 'Authentication failed' error message appeared after entering user name and password when attempting to download a...
This Information Applies To: ICP-MS MassHunter with Spectroscopy Database Administrator (SDA) and Protect Local Data On.
Issue
With Spectroscopy Database Administrator (SDA) and Protect Local Data turned on, batches are not accessible through file...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Scratches on AriaMx optical modules can lead to a reduction in their performance.
Background
Scratches on an AriaMx optical module are shown in Figure 1 .
Figure 1 ....