Hi guys, I'm experiencing regular times ghost peaks starting at 120°C to 295°C.....my setup is GC-FID 6890, Low pressure drop, Ultra Inert Liner with glass wool, column HP1 widebore..... I have cutted the inj/det 5 inches of column, heated at 295°C with…
Troubleshooting report generation in Chemstation. We have successfully generated 100s of reports using the report template and reprocessing when a run is disrupted. I have to sequences that have failed to run a report and I can't get it to via our usual…
The Signal-to-Noise function is better to work with printer, since there are more information on the print out than on screen, virtual printer will also do the job, When you started the function there will be guidance at the bottom of the window, it will…
We recently switched to MH 12.1 for our 6495C. This version of acquisition does not have tune context. Instead the autotune is in the TQ tab of the method.
When I request tune control, it does not change the TQ parameters. It only changes the temps…
Can SimDis data processing be performed manually (i.e. without the aid of additional SimDis software produced by Agilent or a third-party) with a GC running Chemstation?
I'm looking for a low-cost solution to perform SimDis analysis of jet-fuel samples…
We have a GCMS(5975C, intert EI source) which had been out of order since long 6 months due to ALS tray issue. After we installed tray, we cleaned ion source, replaced filaments, cleaned inlet, vent line and replaced split vent trap cartridge. Then tune…
Hello Paul, it looks to me that there is too much acetylene in the gas mixture coming to the burner. This is causing the carbon build-up.
I'd suggest you first remove the absorption cell from the holder and clean this by soaking in dilute nitric acid…
Please try to remove the sample probe and perform the initialization. If it completes successfully make sure the probe is not touching or causing the movement issue. If it failed. Call the response center to get more help with the SPS-4. It could be a…
Hi, I have a GC/MS (8890 GC with 5977b HES MSD) that is also configured with an FID and PDHID. I would like to create an FID/PDHID-only method, where the MSD remains off the entire run and does not collect data. I haven't figured out how to do this so…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...