Hello taub .
I think it's a corner case issue and you need a support visit from agilent authorized engineer so please request a service visit as its seems that the error is hidden and not straight forward as you mentioned that you changed alot of things…
Good Day.
I have an issue to my result in tcd. My Sample is TOGA using Fid and tcd. now the issue is the detection of H2, N2 and O2 are late. before 4.2 min. now its 6.2. the column is new.
This instrument is used mostly for FID analyses and the second injector is not working. That's the primary reason why the column will be disconnected most of the time. Also to reduce contamination of the ECD, but it sounds like that isn't a huge concern…
Hi Abdul,
From the picture, it appears your FID flame was extinguished. You can put a metal wrench or a mirror at the top of the detector to see if the exhaust contains moisture from the combustion, but a flat baseline at zero output usually means the…
We need to use air generator for 8 GCs with FID Detector. Each FID uses 350 mL/min air. So for 8 FID, 2.8L air will be sufficient? Is it ok to go for an air generator that supply 3L of air/min or we need to go for a higher option? Kindly advise
Thank you for the reply, I will have a go at it tomorrow. So essentially I just need to change one of my internal standard compounds to a normal compound, and use that as a single point calibration? It just seemed logical that every internal standard…
Hi guys, when I tried to run my sequence in GC-FID, the workstation showed "front injectors not detected", and under my method, the configuration showed no injectors. However, the parameters I entered for injection could be found in the GC (7890A) operation…
Hi
I am trying to install the G7201D version of ICP MassHunter on a 1909 Windows 10 laptop.
It goes through the initial process and then errors with a code of 0xe0434352.
Some additional research implies this is a .Net error but a repair install…
Hi everyone
In my company recently we update the Openlab Ezchrom to CDS 2,5.
We have a GC 7820A and when we analyzed Residual dissolvents we have a trouble because between 3 to 5 minutes the detector (FID) get shutdown and this signal of shutdown…
I have Open Lab CDS Chemstation Edition for GC systems and 7890A with FID. I get in vial concentration of an analyte in a sample from calibration curve as ppm. Need to generate an Intelligent report, I get concentration in sample (with Sample weight,…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...