The file is a pre-set qPCR program to run a plate filled with water used to test the basic raw fluorescence signal of AriaMx Optical modules.
File required for Performing a Background Calibration
The GC cycle time should be the time from injection until the GC is ready to run again. This includes the analysis run, cool down, and equilibration. Based on the times you listed, it would be roughly 40 minutes. It may be worth timing to make sure. The…
Hi howard_sanford, my apologies for a slow response, but thank you very much for the help and advice. I was able to get the filter for Cal and CC to work, and I appreciate the discussion of my larger problem. I think I'm probably several (many) steps…
Hello, thank you for your help. I had tried loading different processing methods but I didn't realize the results were not linked to any method. It turns out the result files were read-only and could not be linked to any method. I moved the result files…
The peaks look similar, essentially the same sensitivity. I'd look at the background on your older runs and the background now. It could be that most of the previous background was one, two, a few, ions and they're gone now. Was that small but still noticeable…
That is one failure mode of Platinum Resistance Thermometers. It can happen one degree to the next higher degree. The heater/sensor must be replaced, part number G1099-60107.
See also: (+) AUX 2 heater fault - Forum - GC/MS - Agilent Community
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...