While running oils and extracts on GC,the basline shows wandering as in the attached photo below in the range from 75 to 100 mins.The problem is not related to specific temperature because it appears at the beginning of the run,middle and at the end in…
Here is a collection of Agilent 7890, 8860 and 8890 GC Resources. Links to user manuals, troubleshooting resources , tools and supplies on Agilent.com . Go to Collection of GC/MS Resources to view GC/MS information.
Agilent 8890 GC User Manuals
…
Hi Mohammad, Thanks for your thought, detector temperature is not extremely high or low. I did monitor temperature for FID and inlet the whole time even during the injection. It was stable and maintained for hours/days. Method that I was using I had checked…
Hello everyone,
I have a 8890 GC-FID that I've just started running.
I want to create a "shut down" method that turns off (or lowers) H2 and Air once a run is completed or that can uploaded at the end of the day. The goal here is to keep the instrument…
Hello,
I use HS/GC/FID for quantification of caprylyl glycol in moisturizer. After the run, the cap of the vial is dirty, I find the moisturizer on even if the vial is correctly close.
I don't know how can I clean the oven of the HS. I use a headspace…
I am running terpenes on an HP-6890 with an autosampler and an FID, injecting 1 ul using 10:1 split with hydrogen as a carrier gas. I observed that when my standards are dissolved in MeOH the response of all peaks is about 1/4 of that in Heptane. What…
Dear Agilent,
I am trying to perform a "backflush scouting run", using the nice backflush wizard option in Chemstation rev. C.01.10, for configuration of a useful backflush time to my GC method. However, the backflush wizard unfortunately stops after…
No, the flows on the two columns downstream of the switch have to be equal. They are feed by the same pressure source, so since MSD is under vacuum and the FID is ambient, the column connected to the MSD has to have more restriction, to keep the flows…
Can SimDis data processing be performed manually (i.e. without the aid of additional SimDis software produced by Agilent or a third-party) with a GC running Chemstation?
I'm looking for a low-cost solution to perform SimDis analysis of jet-fuel samples…
Agilent GC 7890A, FID, Split Liner. I'm setting up the column to do Hexane injection testing. It was set up this way previously but the program had been deleted and the column removed before I started here. Front Detector/Column which is below baseline…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...