I have recently ran two standards on the Cary 630 FT-IR using the ATR module - qualitative search. One is Heptanes and the other is N-Heptane.
I then ran four samples - three were N-Heptane, the other was Heptanes and compared them to the two standards…
I went through everything I could find, but it appears that BootP doesn't work properly in Windows 10 and even when you follow the instructions it fails. As I mentioned above, the only way I found to get it working was to replace the JetDirect card with…
megaflorch - this was fairly old topic and I wasn't sure if you completed your standards/sample prep. I use a similar technique to get my analytes within a better working linear range with respect to my GC-FID. Your logic is good.... here is my standard…
I have Chemstation C.01.08 [210]. Whenever I try to run a partial sequence, I get the 'Initialization of Sequence Failed' error message. From what I could find online, that issue was supposed to be solved in C.01.08 version of the software. I have Unique…
I am having trouble separating methyl methacrylate (MMA) from another peak. The interfering compound, appearing in the front, is identified by library as 3,3-dimethyl-2-butanone and it is inherent to the sample. MMA appears as the split/tailing peak.…
You can definitely set up an intelligent report to do what you want, but there is a much easier way to do this in OpenLAB ChemStation. When you create a calibration table, ChemStation gives you an option to 'Calculate Signals Separately': When selected…
I did a lens ramp on the failed BFB_AT and the emission ramp for 50 amu was very choppy. Setting the emission at 50 amu is where the tune process fails. Could this be due to a hardware problem?
Hi,
I am currently running a USP <467> protocol which monitors the recovery of: methanol, ethanol, acetone, isopropyl alcohol, hexanes, and toluene. I make a standard solution using DMAC with known amounts of solvent and use the same solution to spike…
Hi Lakshmi, Here is the reply from our compliance group.... Traceability and Audit Trails Data are generated by the same native chromatography data system (CDS) used in the daily operation of the instrument, which controls the system being qualified during…
Hi,
Every time we vent and vacuum down the MS2 auto tune fails with the high mass.
I've tried to tune from factory settings and manual tune using a file that was used prior to the shutdown.
The instrument is second hand so we have had the vendor…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...