Hi everyone,
We have detected fails in 3 FLD modules installed in the same instrument.
The fist of these gave the error 06712 (emission motor did not find position),and was replaced with a second module. This when it was being installed failed again…
Hi Lars, I would add an input from my experience that H2 carrier gas may cause some chemical reactions on some specific polar columns and compounds. Two scenarios I have encountered were (1) analysis of C4-C5 olefins on an AL2O3 PLOT column where some…
I get a bunch of junk on the front panel of the GC and the detectors I have (PID and FID) end up going cold. It is a bunch of work to re-calibrate due to software stuff we have to do for the method we are running. Plus the 1/2 hr runs I do take a while…
Hi All,
For the last 1.5 years, the pump has been running fine even though the rear seal wash was blocked. Then in September, we were having issues with our pumps and found there was leaking in pump B. We did a maintenance, meaning cleaning the pumps…
Hi Azrael, Publication Part Number: A02028 might be one of several apps to look at. if you could elaborate which targets are nice but not required for quantitation? It appears that Argon is the carrier and sample prep diluent gas then, though He/H2 are…
Hello, SW: MassHunter Workstation, Quantitative Analysis, Drug Analysis for GC, Version 10.1 Build 10.1.733.0 I am trying to batch process data acquired by GC-FID but I unable to generate the correct sample result since I don't know where to enter the…
Hello, I have a TCD + FID GC 6890. Need to upgrade to Windows 10, because Windows will no longer provide security updates for Windows 7. Is Chemstation B.04.03 compatible with windows 10? Alternatively, will A.10.02 be compatible with GC6890? Thanks for…
I have been operating an 7890A/5975C with Chemstation version E.02.00.493 for a couple of years. The autosampler is a Gerstel MPS2 (model MXY-02-00B) controlled by Maestro version 1.10[017] and the GC has an FID in the front detector position. I have…
I have configured my laptop to our 8890 GC with a split/splitless inlet and FID. I am currently just doing manual injection. When sending the method from my laptop to the instrument, all of the parameters reach the setpoints except for my column temperature…
Hello,
we want to analyse a gas mixture (CO2, CO, propane, ethane and methane in hydrogen) with the HP 6890 Series GC System (G1540A). The gases are coming to the column via a six-way valve and after the column, there is a TCD and a FID detector. In…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...