Hello,
You turned the value back into a number by dividing by10 outside the formatnumber statement. I would just place the entire statement in a Val() function and then format the column as 1 decimal place.
Marty
=Val( If ( Signal_Name like…
Hello staceylouie ,
I apologize for the delayed response.
The error you are seeing was a known issue in that revision due to no structure match being found for the selected compound. The workaround for that version was to click the Continue button…
Dear LD,
If your experiment requires precise control over calcium levels, EGTA should be preferred due to its higher selectivity for calcium ions. However, if calcium levels are not critical or can be adjusted accordingly, EDTA may be a suitable alternative…
Dirty, damaged, or blocked interface cones drastically impact the sensitivity and background of your ICP-MS system. Small/gradual changes in the vacuum level of the interface region is an indicator of cone maintenance. Learn about how to clean and condition…
Learn about how to inspect the torch, bonnet, shield plate, and RF Coil, as well as torch cleaning and handling recommendations for Agilent ICP-MS systems.
Preventative and regular maintenance are crucial in avoiding ignition issues and plasma instability…
Hello clockhar ,
The calibration table is stored in only one sample in the batch. This is why you keep seeing the same accuracy since this is stored in the peak table.
Unfortunately, it would be very difficult to come up with a Report Builder binding…
Here is the contact information for Agilent in Brazil. https://www.agilent.com/sites/agilent/en/contact-us/brazil
The Agilent Salesperson in Brazil is Marcelo Azevedo - marcelo.azevedo@agilent.com
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...