Good morning, everybody!
I am currently doing untargeted analysis using the Unknown analysis software. I could «identify» some compounds of interest, which is great. Now, my next step is to do a semi-quantification of my compounds using my internal…
Hello,
For awhile now, I've been having issues with my resolution axis "passing" for masses 25 and 26 in no gas mode. I have done many cleanings and new tuning solutions. Can anyone explain what is causing this continual failing and what I could do…
Hello Agilent community,
I have recently been 'Recovery Test in GMP' of Openlab 3.4 (Build 3.4.0.242) in a standalone environment using the Windows Hyper-V feature.
During the testing, I found the following two issues
First, a warning message…
Hello everybody,
I operate an Agilent 7890B-GC/5977A-MSD and a 7820A-GC-FID, both with autosampler.
Those systems are yearly maintained by Agilent.
So far, GC-MS is for qualitative analysis (compounds identification through library search for…
I looked at your plot again. That little bounce is barely 0.01pA -- so very tiny! This is down in the lowest possible signals that can be measured with an FID and honestly should not matter as your smallest peaks of interest should be at least 50x to…
We have OpenLab 2.1 (with content manger) running our GC and LC systems. We have successfully been running 2 x GC and 6 x LC systems however this morning on two of the systems we can see the following error:
Acquisition
Failed to connect to the…
We run a lot of our GCs with Polyarcs (methanizers) and FID responses can be theoretically calculated. While upgrading the software and importing chemstation methods, the calibration table did not get imported. If I could manually edit the calibration…
Hello, Just to add on to dnprulz 's reply, the expression that he provided will work in OpenLab Custom Calculator and should perform what you are looking to do. However, if you want the pass/fail logic to be set on the report template then you will want…
After a failed methamphetamine quantitation, it was noticed that the methamphetamine peak shape on our GC/FID instruments has been consistently poor or deteriorating through out a run. This has been happening on both of our GC/FID instruments (all 3 columns…
This Information Applies To: HPLC Advisor app
Issue
The Agilent InfinityLab HPLC Advisor app is a cost-free mobile app for both Android and iOS.
It offers tools to save time with HPLC troubleshooting, method development, and more. Once installed...
This Information Applies To: Agilent 5977A/B GC/MSD with MassHunter GC/MS Acquisition Software
Issue:
This article describes the procedure to safely pump down (start) 5977A/B GC/MSD with Electron Ionization (EI)
Steps To follow:
Before you...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...