Hello, Just to add on to dnprulz 's reply, the expression that he provided will work in OpenLab Custom Calculator and should perform what you are looking to do. However, if you want the pass/fail logic to be set on the report template then you will want…
Hi, I ran my batches with GC-FID under MassHunter Quant, but I cannot generate any reports. The error popped up during generating which is "Error: 'QuantDataProvider' object has no attribute 'FormatDateTime'." Has anybody faced with this issue to help…
Hi
Either there is leak or loop is not filling properly with sample for low area.
And for too hot transferline, may be PC board or sensor is malfunctioning or faulty of headspace.
You can change column or trim the column from inlet and detector…
Update: I checked filament and looks fine. Weird when switching from EI to CI source the tune fails 3x in a row and then passes every time after that. This happened twice after switching source. The tunes that pass though do not seem like everything is…
Hi Tom, we were told to upgrade to version 10.1 and it solved this issue. However, we found different strange behavior of manual integration. General integrator sometimes fail to integrate peak while manually integrating. What I still don't understand…
Hello, From the screenshot you posted the error that appears to be aborting the method run is "Failed to set injection volume". For a headspace sampler the injection volume should be the sample loop volume which is part of the instrument configuration…
Hi all,
I have a 6890A GC with a FID. We recently acquired the instrument and I have been running standards up to test methods. I have been getting signals that seem suspiciously low.
I am injecting Matreya Bacterial CP FAME mix (C11-C20 methyl esters…
We have experienced this but on a 5975. The cooling fan for the turbo pump failed to restart after maintenance. The error message however did not refer to the fan at all. The easiest way to check if the fan is working is to hold a Kimwipe or other tissue…
Hi Brian,
What kind of detector are you using? From my experience with FID, you shouldn’t have issues with septa bleed from re-running samples within the same day. If you inject the vial and then re-run it after a day, you will probably see n-hydrocarbon…
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The following procedure is to learn how to use the tools in the Compound Information window to view chromatograms and spectra for your data.
Steps to follow...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Batch Table can be configured with many different data columns. This article uses an existing demonstration batch with method and analyzed data files to view different...
This Information Applies To: Agilent MassHunter Qualitative Analysis software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Navigator View.
Steps to follow
Note : Use the demonstration data...
This Information Applies To: All versions of Agilent MassHunter Qualitative Analysis Software , and Agilent MassHunter Quantitative Analysis version B08.00 and up
Issue
Calculation of signal-to-noise in MassHunter is performed using the same parameters...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Preparing and running a sample is essential for data acquisition. The steps below detail how to run a single sample using an Automatic Liquid Sampler (ALS) on...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Compound View.
Steps to follow
Note : Use the demonstration data files...
This Information Applies To: Agilent MassHunter qualitative analysis software
Content:
MassHunter can be configured to label TIC chromatographic peaks with the best match compound name from an MS library search.
Steps to follow:
On the top...
This Information Applies To: Agilent MassHunter GC/MS Data Acquisition (Rev. 10.0 and below)
Issue
Users running MassHunter GC/MS Data Acquisition with Microsoft Windows 10, may encounter warning messages about insufficient memory in the PC when...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software, Revision 7 and up
Issue
This article shows the procedure to change the number of decimal places in the Mass Spectrum Preview and MS Spectrum Results windows of the MassHunter...
This Information Applies To: Agilent OpenLab CDS ver. 2.4 or earlier.
Issue:
If the PC name on a system with OpenLab 2.4 or earlier revisions needs to be changed post installation of the software. This must be done in the right way or the instrument...