Hello AGILENT family,
i have a few questions on the analysis of Pb in blood samples.
am failing to get the right concentrations of the QC sample 8ppb instead it’s reading 0.08 ppb and at the same time it’s also showing overange (0.08o) even when my…
I am a user of an Agilent 7900 ICP-MS. It has been working fine since last month, but today (Oct 13, 2022) the software was not able to connect to the instrument. When I try to connect the MassHunter software to the ICPMS by going to settings > mainframe…
Thanks for the answer but I still fail to understand.
If helium pressure at the inlet of the TD is constant and only controlled manually, why can't it be controlled by the AUX EPC?
Can't I just connect one of the outlet of the AUX EPC through a t…
We fail to properly communicate with the turbo V70 controller, model 969-9507, using RS232.
The communication is ok for all commands that do not answer with more than two bytes, like start and stop.
However, commands supposed to answer with more than…
We have a GC-MS instrument and it works well. Recently we installed a new column which connected to FID detector. Now we want to run a method with GC-FID/MS. However, we observed the peaks only in MS spectrum without FID spectrum. We need help with the…
This document contains a list of FAQ and troubleshooting links for Agilent Cell Analysis products. See also Collection of Cell Analysis Resources .
FAQs
Seahorse:
Agilent Seahorse XF Imaging and Normalization FAQs
Agilent Seahorse XF Real…
Hi Everyone
This is my first post here in this community. And I really hope to get some ideas to fix my problem, since i'm getting slowly desperate!
So here's my problem: We have some really bad contamination/peaks on all our polar Systems:
I…
Hi community
we getting error message (Configuration system failed to initialize. Chemstation will shutdown now) when we trying to launch Chemstation ,we try rename conf. files in C:\Chem32\1 but that not work.
I appreciated any help .
Dheya
Hi,
I get this Front Inlet: Septum purge Pre shutdown warning with Error code: 20401202 with cause showing EPC module is going into a shutdown. This warning showed up immediately after the maintenance was performed to change the septum and SSL liner…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, Oligo Pro II, and ZAG
Issue:
Only plasticware from the approved consumables list should be used in the Agilent Parallel Capillary Electrophoresis systems. The use of plasticware...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Question:
Can more than one Agilent 2100 Bioanalyzer instrument be connected to one PC?
Steps to follow:
It is possible to connect a maximum of two Bioanalyzers to one laptop...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer Chip Priming Station: part number 5065–4401
Maintenance procedures and how frequently they are required :
Procedure
Time interval
Or if this issue occurs
Where to find a detailed...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
Running the hardware diagnostics on the Agilent 2100 Bioanalyzer system can help to investigate whether the instrument performs as expected.
Steps to follow:
Required...
This Information Applies To: 2100 Bioanalyzer, RNA 6000 Nano kit, RNA 6000 Pico kit, Small RNA kit
Issue:
Is it possible to size RNA on the Agilent 2100 Bioanalyzer system?
Resolution:
Agilent offers total and small RNA assays on the Bioanalyzer...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue:
The Agilent 2100 Bioanalyzer system does not detect a prepared microfluidic chip after it is inserted into the instrument. The interface shows the instrument...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer chips
Issue:
Can 2100 Bioanalyzer assay chips and reagents be interchanged?
Resolution:
Some assay chips can be used with multiple assays, however some cannot because the chip layout...
This Information Applies To: Agilent MassHunter GC/MS Acquisition software
Issue
The MassHunter software performs several checks during the startup sequence. If it detects a problem, an alert message box will be displayed and the message bar on...
This Information Applies To: Agilent MassHunter Quantitative Data Analysis Software
Issue:
The "NO DATA POINTS" error message appears in the Compound Information window in the lower-left corner in Quantitative Analysis. Sometimes, this problem may...
This Information Applies To: Agilent GC/MSD MassHunter with MSD ChemStation Data Analysis
Issue
When you are using the Data Analysis Report, you may need to specify a certain number of decimal places for your results different to the default decimal...