Hello Martin and Andy! I found out what were wrong. In my sequence two injections doesn't have a DA Method linked. When I pin only the injections with DA Method linked, the "No Data Found" was gone.
Thanks for letting us know. I will look into this and determine why it is not working. In the meantime, the file can be downloaded from the 7820A product page at https://www.agilent.com/en/product/gas-chromatography/gc-systems/7820a-gc-system . Scroll…
Thank you very much for your quick answer. It's very important for me to understand the concept well, so I have some consistency problems with the response of the compounds.
The Digest of upcoming webinars has been updated as of May 23.
The new Agilent Community Group, GPC/SEC Solutions Group hosted a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules …
For more information, check out the application note Five Keys to Unlock Maximum Performance in the Analysis of Over 200 Pesticides in Challenging Food Matrices .
Recommended parts from the video:
Self-tightening, collared column nut for use with…
Hello,
Are you still having low flow issues on your AA? Did replacing the nebulizer assembly help?
Do you change the flame gases for your methods? If so, call up a default air/acetylene method. You will need a lamp of that element. Go to Optimize…
It is hard to see from the picture which stator this is. If it is the 7 port for ISIS3 then the part number of just the stator is:
G8411-80121 Stator, for 7 port, 2 position inject valve.
Hello,
The penning gauge is now referred to as the ion gauge. It is located on the right side, front of the analyzer chamber. It is easily identified by the blue cable connected to the back of the gauge. Make sure to put the instrument into Shutdown…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, Oligo Pro II, and ZAG
Issue:
Only plasticware from the approved consumables list should be used in the Agilent Parallel Capillary Electrophoresis systems. The use of plasticware...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Question:
Can more than one Agilent 2100 Bioanalyzer instrument be connected to one PC?
Steps to follow:
It is possible to connect a maximum of two Bioanalyzers to one laptop...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer Chip Priming Station: part number 5065–4401
Maintenance procedures and how frequently they are required :
Procedure
Time interval
Or if this issue occurs
Where to find a detailed...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
Running the hardware diagnostics on the Agilent 2100 Bioanalyzer system can help to investigate whether the instrument performs as expected.
Steps to follow:
Required...
This Information Applies To: 2100 Bioanalyzer, RNA 6000 Nano kit, RNA 6000 Pico kit, Small RNA kit
Issue:
Is it possible to size RNA on the Agilent 2100 Bioanalyzer system?
Resolution:
Agilent offers total and small RNA assays on the Bioanalyzer...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue:
The Agilent 2100 Bioanalyzer system does not detect a prepared microfluidic chip after it is inserted into the instrument. The interface shows the instrument...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer chips
Issue:
Can 2100 Bioanalyzer assay chips and reagents be interchanged?
Resolution:
Some assay chips can be used with multiple assays, however some cannot because the chip layout...
This Information Applies To: Agilent MassHunter GC/MS Acquisition software
Issue
The MassHunter software performs several checks during the startup sequence. If it detects a problem, an alert message box will be displayed and the message bar on...
This Information Applies To: Agilent MassHunter Quantitative Data Analysis Software
Issue:
The "NO DATA POINTS" error message appears in the Compound Information window in the lower-left corner in Quantitative Analysis. Sometimes, this problem may...
This Information Applies To: Agilent GC/MSD MassHunter with MSD ChemStation Data Analysis
Issue
When you are using the Data Analysis Report, you may need to specify a certain number of decimal places for your results different to the default decimal...