Hello,
I am not sure exactly what you are doing but to use part of the text in an if you can parse apart the text using string functions or use the like comparison. So your =IF(COUNTIF( A2 ,"*mg*"),"Value if true","Value if false") would be =If(A2…
How many total runs on this system?
8890 and Intuvo: Service Mode, Instrument, Usage
7890: Service Mode , Diagnostics, Instrument Status
6890: Options, Diagnostics, Instrument Status
A 6890/5975 probably has many, many runs on it and passed…
There could be issues with either control signals to the HED power supply or the power supplied to the HED power supply. These electronic issues are down in the depths of the instrument and should be handled by a trained service engineer. Please contact…
A bit late maybe, but you can set the printer within the macro using the MYPRINTER = "name of printer". Use the command before your STARTPRINT command, and then at the end of the macro remove it (REMOVE MYPRINTER), so that it will only be active for the…
Here's a link to the video from this event!
(+) Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table - Follow-up Discussion - Forum - Gas Chromatography - Agilent Community
You should always consider that after re-igniting the lamp, it typically requires 60-90 minutes establishing a stable detector signal.
Based on this it does not always make sense and saves lifetime shutting off the lamp.
Keep constant flow 1.2 ml/min into the MS and do a Pulsed Splitless injection, tips in the help section of the Operating manual. Your system's diffusion high vacuum pump can only handle 2.0 ml/min maximum so do not exceed that ever.
If you have a 30m…
In Manual Tune, PFTBA closed, set the scan range to 10-100, then click on the spectrum scan button. The spectrum will show repeatedly in the middle window to the left at the long red arrow..
Beautiful. Does the spacing change with a different column flow rate? If this is 1.2 ml/min, for example, is it different with only 1.0 ml/min? If it changes and you did the inlet and column maintenance properly, the issue is before those. If it does…
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...