Hello,
What version of the software do you have? The version will be something like CDS 2.x where x is the version change. I would guess that you still have injections setup as cal stds and when you reprocess it is clearing and recreating the calibration…
Hello mass_defect ,
There is currently not a workflow for changing the sample name information in MassHunter after the data file has been acquired. There have been enhancement requests made for this feature but there is currently no timeline for when…
Support and educational resources for the Labware MiniHub
Automation Solutions Knowledge Base
Microplate-Handling Device Guides
PDF user guides
Online Labware MiniHub User Guide
Opening Labware MiniHub Diagnostics
Creating Labware MiniHub…
To enable the Net.TCP Port Sharing Service using MMC
From the Start menu, open the Services Management Console either by opening a Command Prompt window and typing services.msc or by opening Run and typing services.msc into the Open box.
In…
This video guides you through the process of removing the capillary on a system with a VacShield and applies to G6470B, G6475A, G6495C, G6495D, Ultivo (G6465A, G6465B) iQ (G6160A), and Revident (G6575A).
This video is intended to support the written…
This video guides you through the process of installing and removing a capillary with a gate valve and applies to G6495B, G6546A, and 6545XT AdvanceBio (G6549A).
This video is intended to support the written instructions found in the online help or…
New FID Jet!
The latest FID jet is intended for use in 6890/7890/8890/8860/8850/9000 GC models
The legacy jets will not work in the 8890/8850/8860/9000 GC models
The new jet makes installing the column seamless with a conical shape to direct the…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...