I have an agilent GC-FID 6890 i use for TPH and PAH of soil samples yet i want to calibrate it for Oxygenates in gasoline and Aromatics don't know how to go about it
A follow up question about this, if it ever occurs again. When the instrument errored out it prevented us from even initializing the instrument properly. Is it possible to auto reference even if the unit failed to initialize correctly?
Welcome everybody,
The problem occurred after updating Openlab CDS Software 2.2 Version to 2.4 Version.
GC# 7890B With FID , and TCD Detector
OpenLab CDS Software 2.4
After installing the software version 2.4 and after a gas sample injection…
Hello,
I have a question about our GC 8860, which has been experiencing some problems since I changed the valve pressure.
Although it works well immediately after the change, if I don't use the GC for a few days, the first few runs produce larger…
Hi All, I need help to fix either baseline drifted down or change volume injection of water samples in GC/FID. Specifically, I am setting up a new GC instrument for analysis of methanol and alcohols in water samples with the following conditions: - Instrument…
Hi Everyone,
Due to random readings of my samples, i ran wavelength and photometric accuracy test. Both of them fails, do i need to replace the lamp or is it because of the wavelength drive gear?
thanks.
If you want to know what specific module is sending a Leak error, this article in the Knowledge Portal can help:
Determining which Module is Causing the Shutdown Error Due to a Leak
The "Valve command failed transport command failed" Error can have…
The optional high vacuum gauge has a cable between the gauge and the electronics. It is either disconnected or the gauge has failed.
See page 125 and 126 in the 5977B Series MSD Operating Manual for instructions on how to turn it on and off.
The…
When the tuning is done at 3200 (+) everything is fine. When I change it to tune at 1700 (+) the masses are reasonably accurate. After it gets to the third mass (620) it appears that the entire spectrum shifts by about 1.5 AMU and the tuning fails. There…
There is an SP7 switching valve on our 5110 ICP-OES The first set of triplicate aspirations of Std always ride really close to the precision limit of 2%RSD and then std#2 and Std3 are typical 0.5 or less. (ISTD Method) All of these standards are in the…
This Information Applies To: 4150 TapeStation, 4200 TapeStation
Issue
How to deal with a TapeStation Electrode Cartridge change is due warning message.
Background
The Agilent TapeStation controller software will notify users to replace the...
This Information Applies To: Agilent OpenLab CDS
Issue
Sometimes the integration result is not ideal for all injections. This article outlines the step-by-step instruction to manually integrate peaks.
Background
There are 2 ways to integrate...
This Information Applies To: Agilent OpenLab CDS , Agilent OpenLab ChemStation
Issue
Calculation of Area percent or Height percent for uncalibrated compounds in OpenLab software. If all components respond equally in the detector, then Area% and...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
How to power off the Agilent ICP-MS Foreline Pump to perform maintenance, or when fully powering off the Agilent ICP-MS System.
Background
The ICP-MS MassHunter...
This Information Applies To: Agilent ICP-MS (7500,7700,8800)
Issue
How to check the E2M18 or E2M18F foreline pump to determine if the pump needs maintenance?
Background
The oil cleanliness and oil level in the E2M18 or E2M18F foreline pump...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the foreline pump oil in the DS 402.
Background
The DS 402 oil should be replaced at least every 3 months or when the oil color indicates it needs to be changed...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue
How to delete data that is stored on the GC instrument.
Steps to follow
Caution : Before deleting data from your GC, Agilent recommends extraction of data as a backup...
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...