Hello,
Are you sure the end tip of the PLOT column ends up (and 2 mm withdrawn) inside the FID Jet?
Any problems when igniting the FID?
FID Jet could be contaminated from PLOT stationary phase particles ..
Best regards -
Lars
Here is a collection of Agilent 7890, 8860 and 8890 GC Resources. Links to user manuals, troubleshooting resources , tools and supplies on Agilent.com . Go to Collection of GC/MS Resources to view GC/MS information.
Agilent 8890 GC User Manuals
…
Our lab has an Agilent 1260 Infinity HPLC, and we are encountering an annoying issue with the desktop connected to it. The desktop sometimes shut down automatically, while the HPLC is still running the analysis. The HPLC keeps working and and the analysis…
Hello, anyone here know what happen with my icp-oes?
i got error message '' gas scp write channel" and icp-oes unable to running due plasma ignition failed, the icon plasma also blinked many times.
Thank you.
Rerey
The vials and caps are the same ones we have been using for years now; they are your standard 2mL GC/LC vials. I opened up LabAdvisor and ran the gripper test. It failed to release the vials even after re-initialization. I removed the gripper caps, wiped…
Hello,
I am new to MassHunter, so this may be a basic question or just something I'm doing wrong. I am trying to build a quantitation method for a large number of compounds we are analyzing via LCMS. I ran our calibrators with our LCMS method and have…
Hi
When FID is off means no flame.
Voltage applied during ignition and while FID OFF so ignitor also Off..
When ignitor off then voltage also off...
Hope, it's clear to you..
The Pfeiffer turbopump on my 5977C MSD will not start after shutdown; it does not exceed 5%. When I boot the MSD, the green LED on the pump controller is solid. Then when the turbo fails to reach 80%, the LED starts blinking and the MSD panel returns…
If your area is relatively stable but your amount/result is low, you have to have either altered your calibration values, failed to clear a previous calibration, or omitted a dilution factor. Are all results lower by the same factor or is it variable…
This Information Applies To: 4150 TapeStation, 4200 TapeStation
Issue
How to deal with a TapeStation Electrode Cartridge change is due warning message.
Background
The Agilent TapeStation controller software will notify users to replace the...
This Information Applies To: Agilent OpenLab CDS
Issue
Sometimes the integration result is not ideal for all injections. This article outlines the step-by-step instruction to manually integrate peaks.
Background
There are 2 ways to integrate...
This Information Applies To: Agilent OpenLab CDS , Agilent OpenLab ChemStation
Issue
Calculation of Area percent or Height percent for uncalibrated compounds in OpenLab software. If all components respond equally in the detector, then Area% and...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
How to power off the Agilent ICP-MS Foreline Pump to perform maintenance, or when fully powering off the Agilent ICP-MS System.
Background
The ICP-MS MassHunter...
This Information Applies To: Agilent ICP-MS (7500,7700,8800)
Issue
How to check the E2M18 or E2M18F foreline pump to determine if the pump needs maintenance?
Background
The oil cleanliness and oil level in the E2M18 or E2M18F foreline pump...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the foreline pump oil in the DS 402.
Background
The DS 402 oil should be replaced at least every 3 months or when the oil color indicates it needs to be changed...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue
How to delete data that is stored on the GC instrument.
Steps to follow
Caution : Before deleting data from your GC, Agilent recommends extraction of data as a backup...
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...