Thank you sir for the best answers.
I have another question to ask.
My new MPAES 4210 is just a year old. My plan is to Analyse metals for Lube Oil Condition Monitoring for mine fleets.
However, I find bit difficult to get the correct calibration…
Our lab just got a GC/MS-FID installed and we are using MSD Chemstation data analysis instead of mass hunter. However, is there a way to only integrate the GC-FID tic and not the tic used for mass spec? (I hope that makes since) Or is it set up to integrate…
Abdoul-
From your description (instrument configuration fails), it sounds like you will need to remove and re-install MH Acquisition. You might try a repair of the software.
Pinging 192.168.254.12 only confirms that the MS is communicating with…
Thank you very much! I'll make sure to have those items correctly. Our instrument (5975C MSD) has been in idle condition for over an year but under vacuum up until recently I started it again. My real issue is autotune fail. The tune fail symptom is Ent…
I am having difficulty with lighting the FID on my 5890 GC. I took apart the detector and cleaned as best as I could. I removed the jet and cleaned it on a sonicating bath. However, I am still unable to thread a syringe cleaning wire through the jet.…
Hello Kang: Generally, and aging lamp would be the likely cause of this problem. The average life of the 8453 lamp is 1000 hours. Lamp performance and lifetime may also be affected by physical shock while the lamp is hot, igniting the lamp while it's…
Your second sample set did not start because there is a conflict that could not be resolved. Instrument failures can be separated into method or sequence.
If you select your (failing) instrument method and press "Setup", does the instrument start equilibrating…
I have a 7890 and 5977a which have been sitting for a few years as the result of a failed business venture, I did some successful spme analysis on it a year or so back but just tried some tests from the ALS and it fails. I'm an absolute novice with this…
Hi Carol_Ultivo , There is always a trade-off or balance to be struck between Scan speed, mass resolution and sensitivity in any quadrupole mass filter. So, if you decrease the resolution and keep scan speeds the same you will naturally get an increase…
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...