Hi, I ran my batches with GC-FID under MassHunter Quant, but I cannot generate any reports. The error popped up during generating which is "Error: 'QuantDataProvider' object has no attribute 'FormatDateTime'." Has anybody faced with this issue to help…
After a failed methamphetamine quantitation, it was noticed that the methamphetamine peak shape on our GC/FID instruments has been consistently poor or deteriorating through out a run. This has been happening on both of our GC/FID instruments (all 3 columns…
Hi everyone,
We are using a UV-VIS-NIR model Cary 5000. Recently when we validated the instrument. However, at the wavelength accuracy test using the Deuterium lamp, we found that 486 and 656.1 nm emission lines have been split into two emission lines…
Hello jeremy_lai ,
In your expressions you must check for both the existence of the qualifier and the outlier yourself. In the initial if and in the final one you need to add a check to see if there is a qualifier by checking to see if it is None. …
Hi
Either there is leak or loop is not filling properly with sample for low area.
And for too hot transferline, may be PC board or sensor is malfunctioning or faulty of headspace.
You can change column or trim the column from inlet and detector…
Troubleshooting report generation in Chemstation. We have successfully generated 100s of reports using the report template and reprocessing when a run is disrupted. I have to sequences that have failed to run a report and I can't get it to via our usual…
Hi Brian,
What kind of detector are you using? From my experience with FID, you shouldn’t have issues with septa bleed from re-running samples within the same day. If you inject the vial and then re-run it after a day, you will probably see n-hydrocarbon…
While running oils and extracts on GC,the basline shows wandering as in the attached photo below in the range from 75 to 100 mins.The problem is not related to specific temperature because it appears at the beginning of the run,middle and at the end in…
We have a GCMS(5975C, intert EI source) which had been out of order since long 6 months due to ALS tray issue. After we installed tray, we cleaned ion source, replaced filaments, cleaned inlet, vent line and replaced split vent trap cartridge. Then tune…
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...