Is the MS still pumped down and ready to go? Do you have -- Use the MS -- checked in the method? If the column is connected to the FID and the MS is not running you'll need to uncheck that and save the method, hopefully with a new name like No_MS_FID_Only_28Feb2023…
Hello, is it possible to operate a HP 5890 II with 7673 in standalone mode completely without computer/integrator?
I'm trying to set up a GC taken from a former GC-MS system working with a PC over GPIB. It should now work as GC-FID together with the…
I am getting message "draw command failed, EE34205" while running batch in G7129B infinity 2 autosampler. I have tried replacing transport assembly, but error is same. I have used another module G7129A Infinity autosampler with this LC, but same error…
Hi Ran,
Thank you for contacting us and I am sorry to hear that you are observing this issue. Based on the symptoms observed (low signal intensity causing the lower markers not to be detected combined with the autofocus failure) may indicate hardware…
Hi,
I removed Heater/sensor assy from Back channel and put in front channel FID and again reconfigure FID.
Upto now, it's working.
Means Heater/sensor assy was faulty.
But still, one thing I am unable to understand that Fid block was heating earlier…
The computer suffered a firmware downgrade and now it has firmware A.1.08 which we need to update to maybe A.1.16 or A.1.12 but the pc has windows XP. (currently it is giving us an error "AUX HEATER 2 FAULT ") It is a 7890A GC (FID) with MS 5975C that…
Thank you for your response Today when you open the GC we noted the increase returned valid but not connected and the Remote LED off we tried to configuration instrument but a message appears(failed to connect to 6890 at 100.100.100.101)but the GC IP…
Hi, Howard Sanford
Thank you for your replay. The version of MassHunter (MH) Data Acquisition and quantitative analysis programs software is B.07.00.
Unfortunately, there isn’t any error code for this problem. But a window with “The head of file could…
This file contains a list of 86 commonly used consumables and parts for 8860 and 8890 GC .
Upload this file to your Smart Alerts software to automatically add these parts to the Master Parts List
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...